Roof Headlining (For Single Cab) Removal
PRECAUTION (w/ Airbag System)
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
REMOVE FRONT SEAT ASSEMBLY LH
REMOVE FRONT SEAT ASSEMBLY RH
REMOVE FRONT DOOR SCUFF PLATE LH
REMOVE FRONT DOOR SCUFF PLATE RH
REMOVE FRONT DOOR OPENING TRIM LH
REMOVE FRONT DOOR OPENING TRIM RH
REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
REMOVE FRONT PILLAR GARNISH LH
REMOVE FRONT PILLAR GARNISH RH
REMOVE UPPER BACK PANEL GARNISH
REMOVE LOWER QUARTER TRIM PANEL LH
REMOVE LOWER QUARTER TRIM PANEL RH
REMOVE QUARTER INSIDE TRIM BOARD LH
REMOVE QUARTER INSIDE TRIM BOARD RH
REMOVE NO. 1 ROOM LIGHT ASSEMBLY
REMOVE VISOR ASSEMBLY LH
REMOVE VISOR ASSEMBLY RH
REMOVE VISOR HOLDER LH
REMOVE VISOR HOLDER RH
REMOVE ASSIST GRIP
REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
REMOVE NO. 2 HEATER TO REGISTER DUCT
REMOVE NO. 1 HEATER TO REGISTER DUCT
REMOVE NO. 3 HEATER TO REGISTER DUCT
REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)
REMOVE ROOF HEADLINING ASSEMBLY
REMOVE FRONT SIDE RAIL SPACER LH
REMOVE FRONT SIDE RAIL SPACER RH
REMOVE SIDE RAIL SPACER
REMOVE REAR NO. 2 SIDE RAIL SPACER LH
REMOVE REAR NO. 2 SIDE RAIL SPACER RH
Roof Headlining (For Single Cab) -- Removal |
1. PRECAUTION (w/ Airbag System) |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (HILUX_TGN26 RM000004QR1006X.html).
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System) |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3008X.html).
3. REMOVE FRONT SEAT ASSEMBLY LH |
(HILUX_TGN26 RM000000Z8U08XX.html)
4. REMOVE FRONT SEAT ASSEMBLY RH |
for Manual Seat:
- HINT:
- Use the same procedure described for the LH side.
for Bench Seat Type:
(HILUX_TGN26 RM000000Z9000EX.html)
5. REMOVE FRONT DOOR SCUFF PLATE LH |
Put protective tape around the front door scuff plate.
Text in Illustration*1
| Protective Tape
|
Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.
6. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
7. REMOVE FRONT DOOR OPENING TRIM LH |
Remove the front door opening trim.
8. REMOVE FRONT DOOR OPENING TRIM RH |
- HINT:
- Use the same procedure described for the LH side.
9. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip) |
- HINT:
- Use the same procedure for both front No. 1 assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration*1
| Protective Tape
|
10. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip) |
- HINT:
- Use the same procedure described for the LH side.
11. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip) |
- HINT:
- Use the same procedure for both front assist grips.
Remove the 2 screws and front assist grip.
12. REMOVE FRONT PILLAR GARNISH LH |
Detach the 2 clips and 2 guides and remove the front pillar garnish.
13. REMOVE FRONT PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
14. REMOVE UPPER BACK PANEL GARNISH |
Detach the 4 claws, 4 guides and 5 clips and remove the upper back panel garnish.
15. REMOVE LOWER QUARTER TRIM PANEL LH |
Remove the bolt and disconnect the front seat outer belt floor anchor.
Detach the claw, 3 clips and 2 guides and remove the lower quarter trim panel.
16. REMOVE LOWER QUARTER TRIM PANEL RH |
- HINT:
- Use the same procedure described for the LH side.
17. REMOVE QUARTER INSIDE TRIM BOARD LH |
Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration*1
| Protective Tape
|
Remove the bolt and disconnect the front seat belt shoulder anchor.
Detach the 3 clips and remove the quarter inside trim board.
18. REMOVE QUARTER INSIDE TRIM BOARD RH |
- HINT:
- Use the same procedure described for the LH side.
19. REMOVE NO. 1 ROOM LIGHT ASSEMBLY |
Using a screwdriver wrapped with protective tape, detach the 4 claws and remove the lens.
- HINT:
- Protective tape the screwdriver tip before use.
Text in Illustration*1
| Protective Tape
|
Remove the 2 screws and remove the No. 1 room light assembly.
Disconnect the connector.
20. REMOVE VISOR ASSEMBLY LH |
Detach the guide.
Remove the 2 screws and visor.
21. REMOVE VISOR ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
22. REMOVE VISOR HOLDER LH |
Remove the screw.
Detach the 2 claws and remove the visor holder.
23. REMOVE VISOR HOLDER RH |
- HINT:
- Use the same procedure described for the LH side.
Using a screwdriver, detach the 4 claws and open the 2 covers.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration*1
| Protective Tape
|
Remove the 2 screws and assist grip.
25. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
(HILUX_TGN26 RM000003O1000KX.html)
26. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.
27. REMOVE NO. 2 HEATER TO REGISTER DUCT |
Remove the 3 clips and No. 2 heater to register duct.
28. REMOVE NO. 1 HEATER TO REGISTER DUCT |
Remove the clip.
Detach the 3 claws and remove the No. 1 heater to register duct.
29. REMOVE NO. 3 HEATER TO REGISTER DUCT |
Remove the clip.
Detach the 4 claws and remove the No. 3 heater to register duct.
30. REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster) |
Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.
31. REMOVE ROOF HEADLINING ASSEMBLY |
Detach the 4 clamps from the front pillar.
Disconnect the connectors and detach the 4 clamps.
Using a clip remover, remove the 5 clips.
Remove the roof headlining as shown in the illustration.
- NOTICE:
- Be careful not to damage the roof headlining when removing it.
32. REMOVE FRONT SIDE RAIL SPACER LH |
Detach the 2 claws and remove the front side rail spacer.
33. REMOVE FRONT SIDE RAIL SPACER RH |
- HINT:
- Use the same procedure described for the LH side.
34. REMOVE SIDE RAIL SPACER |
Detach the 2 claws and remove the side rail spacer.
35. REMOVE REAR NO. 2 SIDE RAIL SPACER LH |
Detach the 2 claws and remove the rear No. 2 side rail spacer.
36. REMOVE REAR NO. 2 SIDE RAIL SPACER RH |
- HINT:
- Use the same procedure described for the LH side.