Drivetrain. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
A750F Automatic Transmission Transaxle. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
INSPECT SPEED SENSOR SP2 INSTALLATION
CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - TCM)
DTC P0722 Output Speed Sensor Circuit No Signal |
DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the TCM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.The gear shift point and lock-up timing are controlled by the TCM based on the signals from this vehicle speed sensor and the throttle position sensor signal.
| DTC Code | DTC Detection Condition | Trouble Area |
| P0722 | All conditions are met 500 times or more continuously (2-trip detection logic): (a) No signal from speed sensor SP2 is input to the TCM while 4 pulses of the No. 1 vehicle speed sensor signal are sent. (b) Vehicle speed is 9 km/h (6 mph) or more for at least 5 sec. (c) Park/neutral position switch is OFF. (d) Transfer is not in neutral. |
|
Reference: Inspect using an oscilloscope.
Check the waveform of the TCM connector.- Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition C24-30 (SP2+) - C24-29 (SP2-) 2 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph) Refer to illustration
MONITOR DESCRIPTION
The output speed sensor SP2 monitors the output shaft speed. The TCM controls the gear shift point and lock-up timing based on the signals from the output speed sensor SP2 and throttle position sensor.If the TCM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The TCM will illuminate the MIL and store a DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the GTS, read the Data List.
ECT Tester Display Measurement Item/Range Normal Condition Diagnostic Note SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) - - HINT:
- SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit. - The SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed:
Sensor trouble, improper installation, or intermittent connection trouble in the circuit.
| 1.INSPECT SPEED SENSOR SP2 INSTALLATION |
Check the speed sensor SP2 installation.
- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
Text in Illustration *a CORRECT *b INCORRECT
 |
|
| ||||
| OK | |
| 2.INSPECT SPEED SENSOR SP2 |
 |
Disconnect the speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition 1 - 2 20°C (68°F) 560 to 680 Ω
Text in Illustration *a Component without harness connected
(Speed Sensor SP2)
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - TCM) |
Disconnect the TCM connector.
 |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition C24-30 (SP2+) - C24-29 (SP2-) 20°C (68°F) 560 to 680 Ω C24-30 (SP2+) - Body ground Always 10 kΩ or higher C24-29 (SP2-) - Body ground Always 10 kΩ or higher
Text in Illustration *a Rear view of wire harness connector
(to TCM)
|
| ||||
| OK | ||
| ||