Dtc P0985 Shift Solenoid E Control Circuit Low (Shift Solenoid Valve Sr)
Drivetrain. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
DESCRIPTION
MONITOR DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
INSPECT SHIFT SOLENOID VALVE SR
DTC P0985 Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR) |
DTC P0986 Shift Solenoid "E" Control Circuit High (Shift Solenoid Valve SR) |
DESCRIPTION
Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In the case of an open or short circuit, the TCM stops sending current to the circuit. For details, refer to the fail-safe chart (HILUX_TGN26 RM000000O8L0OLX.html).DTC Code
| DTC Detection Condition
| Trouble Area
|
P0985
| TCM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip detection logic).
| - Short in shift solenoid valve SR circuit
- Shift solenoid valve SR
- TCM
|
P0986
| TCM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip detection logic).
| - Open in shift solenoid valve SR circuit
- Shift solenoid valve SR
- TCM
|
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve SR is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve SR circuit.When shift solenoid valve SR is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve SR circuit (HILUX_TGN26 RM000000O8L0OLX.html).
WIRING DIAGRAM
INSPECTION PROCEDURE
- HINT:
- Shift solenoid valve SR is turned ON/OFF normally when the shift lever is in D.
TCM gear shift command
| 1st
| 2nd
| 3rd
| 4th
| 5th
|
Shift solenoid valve SR
| OFF
| OFF
| OFF
| OFF
| ON
|
| 1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR) |
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
7 (SR) - Body ground
| 20°C (68°F)
| 11 to 15 Ω
|
Text in Illustration*a
| Component without harness connected
(Transmission Wire)
|
| 2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) |
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
C24-16 (SR) - Body ground
| 20°C (68°F)
| 11 to 15 Ω
|
Text in Illustration*a
| Rear view of wire harness connector
(to TCM)
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 3.INSPECT SHIFT SOLENOID VALVE SR |
Remove shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body
| 20°C (68°F)
| 11 to 15 Ω
|
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
| Specified Condition
|
- Battery positive (+) → Shift solenoid valve SR connector
- Battery negative (-) → Shift solenoid valve SR body
| Valve moves and makes an operating noise
|
Text in Illustration*a
| Component without harness connected
(Shift Solenoid Valve SR)
|
