INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (w/o Front Passenger Airbag)
INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (w/o Console Box, w/o Console Box Lid)
INSTALL AIR CONDITIONER CONTROL ASSEMBLY (for Manual Cooler System)
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Lower Instrument Panel -- Installation |
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (HILUX_TGN26 RM00000118R007X.html).
| 1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
for Automatic Air Conditioning System:
Connect the room temperature sensor.
Attach the 2 guides to install the lower instrument panel.
Connect the connectors and attach the clamps.
Connect the hood lock control cable, fuel lid lock control cable and DLC3.
Install the 2 bolts <C>, nut <D> and 3 screws <E>.
Install the 2 clips <B>.
Text in Illustration *1 Clip <B> *2 Bolt <C> *3 Nut <D> *4 Screw <E> *5 Hood Lock Control Cable *6 Fuel Lid Lock Control Cable *7 DLC3 *8 Clamp *9 Guide - -
| 2. INSTALL NO. 1 SWITCH HOLE BASE |
Attach the 5 claws to install the No. 1 switch hole base.
| 3. INSTALL SWITCH BASE |
Connect the connectors.
Attach the 8 claws to install the switch base.
| 4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (w/o Front Passenger Airbag) |
 |
Attach the 2 hinges to install the glove compartment door.
Text in Illustration *1 Hinge
While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
Text in Illustration *1 Stopper
 |
| 5. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (w/o Console Box, w/o Console Box Lid) |
Attach the 3 claws to install the lower center instrument panel finish panel.
Install the 2 clips <B>.
| 6. INSTALL AIR CONDITIONER CONTROL ASSEMBLY (for Manual Cooler System) |
Connect the connector and install the air conditioning control assembly.
| 7. INSTALL NO. 1 INSTRUMENT PANEL BOX |
Connect the connectors and attach the clamp.
Install the No. 1 instrument panel box with the 6 screws <A>.
| 8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.
| 9. INSTALL NO. 3 HEATER TO REGISTER DUCT |
Attach the 4 claws to install the No. 3 heater to register duct.
Install the clip.
| 10. INSTALL NO. 1 HEATER TO REGISTER DUCT |
Attach the 3 claws to install the No. 1 heater to register duct.
Install the clip.
| 11. INSTALL NO. 2 HEATER TO REGISTER DUCT |
Install the No. 2 heater to register duct with the 3 clips.
| 12. INSTALL COWL SIDE TRIM BOARD LH |
Attach the 2 clips to install the cowl side trim board.
Install the clip.
Install the front door opening trim.
| 13. INSTALL COWL SIDE TRIM BOARD RH |
- HINT:
- Use the same procedure described for the LH side.
| 14. INSTALL FRONT DOOR SCUFF PLATE LH |
for Double Cab:
(HILUX_TGN26 RM00000148N012X_01_0030.html)
for Single Cab:
(HILUX_TGN26 RM00000148N013X_01_0030.html)
| 15. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
| 16. INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid) |
| 17. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY |
| 18. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System) |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (HILUX_TGN26 RM000004QR3009X.html).
| 20. CHECK SRS WARNING LIGHT (w/ Airbag System) |