Dtc P0200 Injector Circuit / Open

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ENGINE CRANKING CONDITION

CHECK ECM

CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE

CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)

REPLACE INJECTOR DRIVER

READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 to #4)

INSPECT INJECTOR ASSEMBLY (RESISTANCE)

INSPECT INJECTOR DRIVER

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

REPLACE ECM

CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)

REPLACE INJECTOR DRIVER

REPAIR OR REPLACE HARNESS OR CONNECTOR

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DESCRIPTION

MONITOR DESCRIPTION

1. P0200 (Open or short in injector driver or fuel injector circuit):
   The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals is inconsistent with the number of INJF signals.
   The injector assemblies are grounded through a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
   After the engine is started, when there is no injection confirmation (INJF) signal sent from the injector driver to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver, DTC P0200 is stored.
   If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
   
   
   
   
   

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

1. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK05BX.html) and initialization (HILUX_TGN26 RM000000TIN04CX.html).
   
2. After replacing an injector assembly, the ECM needs registration (HILUX_TGN26 RM0000012XK05BX.html).
   

HINT:

1. When DTC P0200 is stored, the malfunctioning parts can be narrowed down according to fail-safe behavior.
   
1. When a DTC is stored but the engine does not stall, there may be an open circuit or malfunction in the following components which affect the control of individual cylinders.
   
1. The circuit inside an injector assembly.
   
2. The wiring between an injector driver and injector assembly (between terminal IJ1+ and the No. 1 injector assembly, terminal IJ1 and the No. 1 injector assembly, etc.).
   
3. The wiring between an injector driver and the ECM (terminals #10 and #1, etc.).
   
2. When a DTC is stored and the engine stalls, there may be a malfunction in the wiring which affects the control of multiple cylinders.
   
1. Wiring between an injector driver and the ECM (between INJF terminals).
   
2. The power supply wiring.
   
2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
   

1. Check the engine cranking condition.
   
   

   Result

   Result	Proceed to
   Engine does not start*1	A
   Engine starts, but idling is rough*2	B
   Except above	C

   HINT:

   1. *1: Once DTC P0200 is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
      When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Fuel Press" is higher than the value for "Target Common Rail Pressure"
      
   2. *2: DTC P0200 is stored at this time.
      

1. Check the waveform of the ECM connectors using an oscilloscope.
   

2. Check the waveform of the injector driver (EDU) connectors using an oscilloscope.
   

   OK:

   Tester Connection	Condition	Specified Condition
   C22-24 (#1) - C23-7 (E1)	Cranking	Correct waveform is as shown
   C22-23 (#2) - C23-7 (E1)	Cranking	Correct waveform is as shown
   C22-22 (#3) - C23-7 (E1)	Cranking	Correct waveform is as shown
   C22-21 (#4) - C23-7 (E1)	Cranking	Correct waveform is as shown

   Text in Illustration

   *1	Component with harness connected (ECM)

1. Disconnect the injector driver connectors.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Switch Condition	Specified Condition
   C43-2 (+B) - C43-3 (GND)	Ignition switch ON	11 to 14 V

   Text in Illustration

   *a	Front view of wire harness connector (to Injector Driver)

3. Reconnect the injector driver connectors.
   

1. Disconnect the injector driver connector.
   

2. Disconnect the ECM connector.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   
   

   Tester Connection	Condition	Specified Condition
   C45-4 (#10) - C22-24 (#1)	Always	Below 1 Ω
   C45-8 (#20) - C22-23 (#2)	Always	Below 1 Ω
   C45-7 (#30) - C22-22 (#3)	Always	Below 1 Ω
   C45-3 (#40) - C22-21 (#4)	Always	Below 1 Ω
   C45-5 (INJF) - C22-25 (INJF)	Always	Below 1 Ω
   C45-4 (#10) or C22-24 (#1) - Body ground	Always	10 kΩ or higher
   C45-8 (#20) or C22-23 (#2) - Body ground	Always	10 kΩ or higher
   C45-7 (#30) or C22-22 (#3) - Body ground	Always	10 kΩ or higher
   C45-3 (#40) or C22-21 (#4) - Body ground	Always	10 kΩ or higher
   C45-5 (INJF) or C22-25 (INJF) - Body ground	Always	10 kΩ or higher

4. Reconnect the injector driver connector.
   

5. Reconnect the ECM connector.
   

1. Replace the injector driver (HILUX_TGN26 RM000004QZ2007X.html).
   

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
   

4. Start the engine.
   

5. Read the Injection Feedback Val #1 to #4 values while idling the engine.
   
   

   Standard Value:

   
   

   Item	Engine Speed*	Reference Value
   Injection Feedback Val #1 to #4	Idling	+3.0 mm3/st or less

   HINT:

   1. *: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
      
   2. Fuel is not being injected in cylinders whose "Injection Feedback Val" is higher than 3 mm³/st. Inspection procedures beyond this point diagnose whether there are internal problems with fuel injectors, or whether there is a problem in the wiring of the fuel injector system.
      

1. Disconnect the fuel injector connectors.
   

2. Measure the resistance of the fuel injector
   

   OK:

   No open or short circuit malfunction.
   

   Text in Illustration

   *1	Component without harness connected (Fuel Injector)

3. Reconnect the fuel injector connectors.
   

1. Disconnect the fuel injector connectors for all cylinders.
   

2. Check the waveform of the fuel injector connectors using an oscilloscope.
   

   OK:

   Tester Connection	Condition	Specified Condition
   C1-1 - C1-2	Cranking	Voltage increases by 50 V or more
   C2-1 - C2-2	Cranking	Voltage increases by 50 V or more
   C3-1 - C3-2	Cranking	Voltage increases by 50 V or more
   C4-1 - C4-2	Cranking	Voltage increases by 50 V or more

   Text in Illustration

   *1	Front view of wire harness connector (to Fuel Injector)

1. Replace the injector assembly (HILUX_TGN26 RM000002SY1021X.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY8025X_01_0002.html).
   

1. Register the injector compensation code (HILUX_TGN26 RM0000012XK05BX_02_0003.html).
   

2. Perform the injector pilot quantity learning (HILUX_TGN26 RM0000012XK05BX_02_0009.html).
   

1. Replace the ECM (HILUX_TGN26 RM0000013Z001IX.html).
   

1. Disconnect the injector assembly connectors.
   

2. Disconnect the injector driver connectors.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   
   

   Tester Connection	Condition	Specified Condition
   C1-1 - C43-1 (IJ1+)	Always	Below 1 Ω
   C1-2 - C44-6 (IJ1-)	Always	Below 1 Ω
   C2-1 - C43-6 (IJ2+)	Always	Below 1 Ω
   C2-2 - C44-4 (IJ2-)	Always	Below 1 Ω
   C3-1 - C43-5 (IJ3+)	Always	Below 1 Ω
   C3-2 - C44-2 (IJ3-)	Always	Below 1 Ω
   C4-1 - C44-3 (IJ4+)	Always	Below 1 Ω
   C4-2 - C44-5 (IJ4-)	Always	Below 1 Ω
   C1-1 or C43-1 (IJ1+) - Body ground	Always	10 kΩ or higher
   C1-2 or C44-6 (IJ1-) - Body ground	Always	10 kΩ or higher
   C2-1 or C43-6 (IJ2+) - Body ground	Always	10 kΩ or higher
   C2-2 or C44-4 (IJ2-) - Body ground	Always	10 kΩ or higher
   C3-1 or C43-5 (IJ3+) - Body ground	Always	10 kΩ or higher
   C3-2 or C44-2 (IJ3-) - Body ground	Always	10 kΩ or higher
   C4-1 or C44-3 (IJ4+) - Body ground	Always	10 kΩ or higher
   C4-2 or C44-5 (IJ4-) - Body ground	Always	10 kΩ or higher

4. Reconnect the injector assembly connectors.
   

5. Reconnect the injector driver connectors.
   

1. Replace the injector driver (HILUX_TGN26 RM000004QZ2007X.html).
   

1. Repair or replace the harness or connector.
   

1. Connect the intelligent tester to the DLC3.
   

2. Clear the DTCs (HILUX_TGN26 RM000000PDK0XBX.html).
   

3. Turn the ignition switch off for 30 seconds or more.
   

4. Start the engine and idle it for 10 seconds.
   

5. Enter the following menus: Powertrain / Engine and ECT / DTC.
   

6. Confirm that the DTC is not output again.