2Tr-Fbe Engine Control. Dtc P0335 Crankshaft Position Sensor A Circuit

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

2Tr-Fbe Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

DTC P0335 Crankshaft Position Sensor "A" Circuit

DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth, with 2 teeth missing for detecting TDC, and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM determines the cylinder status based on the G2 signals and detects the crankshaft angle and engine speed from the NE signals.

DTC No.	DTC Detection Condition	Trouble Area
P0335	Either condition is met: No crankshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic). No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).	Open or short in crankshaft position sensor circuit Crankshaft position sensor Crankshaft position sensor plate Camshaft position sensor ECM
P0339	Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic): (a) The engine speed is 1000 rpm or more. (b) The starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off.	Open or short in crankshaft position sensor circuit Crankshaft position sensor Crankshaft position sensor plate ECM

Reference: Inspection using an oscilloscope
HINT:
1. The correct waveforms are as shown.
2. G2 is the camshaft position sensor signal, and NE+ is the crankshaft position sensor signal.
3. Grounding failure of the shielded wire may cause noise in the waveforms.
  Item
  Content
  ECM Terminal Name
  CH1: G2 - NE-
  CH2: NE+ - NE-
  Tester Range
  5 V/DIV.
  20 ms./DIV.
  Condition
  Idling with warm engine

WIRING DIAGRAM

Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fbe Engine Control.Sfi System.
Dtc
P0335 Crankshaft Position Sensor A Circuit

INSPECTION PROCEDURE

Before inspecting the crankshaft position sensor, perform the following inspections which concern the camshaft position sensor.

Check that the camshaft position sensor connector is securely connected, is not loose, does not rattle, etc.
Check that the camshaft position sensor is not loose, does not rattle, etc.
Check that the camshaft timing gear is installed properly.
Perform the Active Test under the conditions* from the time the noise occurred described by the customer (for example, while driving the vehicle) and check if the noise stops.
HINT:
*: Some examples of conditions are idling, racing the engine and driving at full throttle.

HINT:

Troubleshoot for DTCs P0335 and P0339 first. If the trouble area cannot be determined, there may be a mechanical malfunction.
Check the engine speed. The engine speed can be checked by using the intelligent tester. Follow the procedure below:

Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

The engine speed may be indicated as zero despite the crankshaft revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Turn the tester on.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Start the engine.

Read the values displayed on the tester while the engine is running.
OK:
Correct values are displayed.
HINT:
1. To check the engine speed change, display the graph on the tester.
2. If the engine does not start, check the engine speed while cranking.
3. If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.

Go to step 2

CHECK FOR INTERMITTENT PROBLEMS (HILUX_TGN26 RM000000PDQ0YMX.html)

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

Inspect the crankshaft position sensor (HILUX_TGN26 RM000000VX101LX_01_0001.html).

REPLACE CRANKSHAFT POSITION SENSOR (HILUX_TGN26 RM000000VX301JX.html)

OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

Disconnect the crankshaft position sensor connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C6-1 (NE+) - C96-12 (NE+)
Always
Below 1 Ω
C6-2 (NE-) - C96-5 (NE-)
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C6-1 (NE+) or C96-12 (NE+) - Body ground
Always
10 kΩ or higher
C6-2 (NE-) or C96-5 (NE-) - Body ground
Always
10 kΩ or higher

Reconnect the ECM connector.

Reconnect the crankshaft position sensor connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

Check the crankshaft position sensor installation condition.
OK:
Sensor is installed correctly.

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (HILUX_TGN26 RM000000VX001QX.html)

OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

Check the teeth of the sensor plate.
OK:
Sensor plate teeth do not have any cracks or deformation.

REPLACE CRANKSHAFT POSITION SENSOR PLATE

REPLACE ECM (HILUX_TGN26 RM000000VW2024X.html)

Item	Content
ECM Terminal Name	CH1: G2 - NE- CH2: NE+ - NE-
Tester Range	5 V/DIV. 20 ms./DIV.
Condition	Idling with warm engine

Tester Connection	Condition	Specified Condition
C6-1 (NE+) - C96-12 (NE+)	Always	Below 1 Ω
C6-2 (NE-) - C96-5 (NE-)	Always	Below 1 Ω