Dtc P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
1Gr-Fe Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

ADJUST VALVE TIMING

INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

INSPECT OIL CONTROL VALVE FILTER

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly (for intake camshaft), and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC Code
DTC Detection Condition
Trouble Area
P0016
Deviations in the crankshaft and VVT sensor (for bank 1) signals (2 trip detection logic).
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Camshaft timing oil control valve assembly
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM
P0018
Deviations in the crankshaft and VVT sensor (for bank 2) signals (2 trip detection logic).

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores DTC P0016 (bank 1) or P0018 (bank 2).

CONFIRMATION DRIVING PATTERN


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.1Gr-Fe Engine Control.Sfi System. Dtc P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  9. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0016 or P0018.
  12. Check the DTC judgment result.

    Tester Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
  13. Drive the vehicle for 2 to 3 minutes [E].
    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine and ECT / DTC [G].
  16. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  17. Check the DTC judgment result.
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P0335 (HILUX_TGN26 RM000000TCW0QWX_07.html).
Refer to DTC P0340 (HILUX_TGN26 RM000000WBZ0J5X_07.html).

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include No. 1 cylinder.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    P0016 or P0018 is output
    		A
    P0016, P0018 and other DTCs are output
    		B


B
GO TO DTC CHART (HILUX_TGN26 RM000002ZSO00OX.html)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.


NG
Go to step 4
OK


3.ADJUST VALVE TIMING

  1. Adjust the valve timing (HILUX_TGN26 RM0000015D100CX.html).



NEXT
Go to step 7

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. Inspect the camshaft timing oil control valve assembly (HILUX_TGN26 RM000000Q7403JX.html).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (HILUX_TGN26 RM000000PWP04WX.html)
OK


5.INSPECT OIL CONTROL VALVE FILTER

  1. Remove the oil control valve filter (HILUX_TGN26 RM0000015D100CX.html).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.


NG
REPLACE OIL CONTROL VALVE FILTER
OK


6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

  1. Replace the camshaft timing gear assembly (HILUX_TGN26 RM0000015D100CX.html).


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (HILUX_TGN26 RM000000PDK0X5X.html).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the pending DTCs.

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC P0016 or P0018 is output
    		B


B
REPLACE ECM (HILUX_TGN26 RM000000VW202KX.html)
A

END