Outer Rear View Mirror Inspection

Vehicle Exterior. Corolla. Zre142 Aze141
Mirror (Ext). Corolla. Zre142 Aze141

  1. INSPECT MIRROR SUB-ASSEMBLY RH (w/o Retract Mirror)

  2. INSPECT MIRROR SUB-ASSEMBLY LH (w/o Retract Mirror)

  3. INSPECT MIRROR SUB-ASSEMBLY RH (w/ Retract Mirror)

  4. INSPECT MIRROR SUB-ASSEMBLY (w/ Retract Mirror)

Outer Rear View Mirror -- Inspection



1. INSPECT MIRROR SUB-ASSEMBLY RH (w/o Retract Mirror)


  1. Inspect mirror sub-assembly operation.



      Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

    1. Disconnect the mirror connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → H2-5 (MV)
      Battery negative (-) → H2-4 (M+)
      		Turns upward
      Battery positive (+) → H2-4 (M+)
      Battery negative (-) → H2-5 (MV)
      		Turns downward
      Battery positive (+) → H2-3 (MH)
      Battery negative (-) → H2-4 (M+)
      		Turns left
      Battery positive (+) → H2-4 (M+)
      Battery negative (-) → H2-3 (MH)
      		Turns right
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly RH)
      If the result is not as specified, replace the mirror sub-assembly RH.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → H2-1 (+)
      Battery negative (-) → H2-2 (-)
      		Mirror surface temperature becomes higher
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly RH)
      If the result is not as specified, replace the mirror sub-assembly RH.


2. INSPECT MIRROR SUB-ASSEMBLY LH (w/o Retract Mirror)


  1. Inspect mirror sub-assembly LH operation.



      Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

    1. Disconnect the mirror connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → I2-5 (MV)
      Battery negative (-) → I2-4 (M+)
      		Turns upward
      Battery positive (+) → I2-4 (M+)
      Battery negative (-) → I2-5 (MV)
      		Turns downward
      Battery positive (+) → I2-3 (MH)
      Battery negative (-) → I2-4 (M+)
      		Turns left
      Battery positive (+) → I2-4 (M+)
      Battery negative (-) → I2-3 (MH)
      		Turns right
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly LH)
      If the result is not as specified, replace the mirror sub-assembly LH.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → I2-1 (+)
      Battery negative (-) → I2-2 (-)
      		Mirror surface temperature becomes higher
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly LH)
      If the result is not as specified, replace the mirror sub-assembly LH.


3. INSPECT MIRROR SUB-ASSEMBLY RH (w/ Retract Mirror)


  1. Inspect mirror sub-assembly RH operation.



      Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

    1. Disconnect the mirror connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → H11-3 (MV)
      Battery negative (-) → H11-7 (M+)
      		Turns upward
      Battery positive (+) → H11-7 (M+)
      Battery negative (-) → H11-3 (MV)
      		Turns downward
      Battery positive (+) → H11-6 (MH)
      Battery negative (-) → H11-7 (M+)
      		Turns left
      Battery positive (+) → H11-7 (M+)
      Battery negative (-) → H11-6 (MH)
      		Turns right
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly RH)
      If the result is not as specified, replace the mirror sub-assembly RH.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. For each position: Disconnect the battery, set the mirror position by hand, and then connect the battery and check the retractable mirror movement.

    OK:
    Tester Connection
    		Condition
    		Specified Condition
    Battery position (+) → Terminal H11-1 (MR)
    Battery negative (-) → Terminal H11-2 (MF)
    		Forward position (A)
    		Moves from (A) to retracted position (E)
    Battery position (+) → Terminal H11-2 (MF)
    Battery negative (-) → Terminal H11-1 (MR)
    		Forward position (A)
    		Does not move
    Battery position (+) → Terminal H11-1 (MR)
    Battery negative (-) → Terminal H11-2 (MF)
    		Position between forward position (A) and driving position (C)
    		Moves from (B) to retracted position (E)
    Battery position (+) → Terminal H11-2 (MF)
    Battery negative (-) → Terminal H11-1 (MR)
    		Position between forward position (A) and driving position (C)
    		Moves from (B) to forward position (A)
    Battery position (+) → Terminal H11-1 (MR)
    Battery negative (-) → Terminal H11-2 (MF)
    		Driving position (C)
    		Moves from (C) to retracted position (E)
    Battery position (+) → Terminal H11-2 (MF)
    Battery negative (-) → Terminal H11-1 (MR)
    		Driving position (C)
    		Does not move
    Battery position (+) → Terminal H11-1 (MR)
    Battery negative (-) → Terminal H11-2 (MF)
    		Position between driving position (C) and retracted position (E)
    		Moves from (D) to retracted position (E)
    Battery position (+) → Terminal H11-2 (MF)
    Battery negative (-) → Terminal H11-1 (MR)
    		Position between driving position (C) and retracted position (E)
    		Moves from (D) to driving position (C)
    Battery position (+) → Terminal H11-1 (MR)
    Battery negative (-) → Terminal H11-2 (MF)
    		Retracted position (E)
    		Does not move
    Battery position (+) → Terminal H11-2 (MF)
    Battery negative (-) → Terminal H11-1 (MR)
    		Retracted position (E)
    		Moves from (E) to driving position (C)
    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → H11-5 (+)
      Battery negative (-) → H11-4 (-)
      		Mirror surface temperature becomes higher
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly RH)
      If the result is not as specified, replace the mirror sub-assembly RH.


4. INSPECT MIRROR SUB-ASSEMBLY (w/ Retract Mirror)


  1. Inspect mirror sub-assembly LH operation.



      Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

    1. Disconnect the mirror connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → I10-3 (MV)
      Battery negative (-) → I10-7 (M+)
      		Turns upward
      Battery positive (+) → I10-7 (M+)
      Battery negative (-) → I10-3 (MV)
      		Turns downward
      Battery positive (+) → I10-6 (MH)
      Battery negative (-) → I10-7 (M+)
      		Turns left
      Battery positive (+) → I10-7 (M+)
      Battery negative (-) → I10-6 (MH)
      		Turns right
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly LH)
      If the result is not as specified, replace the mirror sub-assembly LH.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. For each position: Disconnect the battery, set the mirror position by hand, and then connect the battery and check the retractable mirror movement.

    OK:
    Tester Connection
    		Condition
    		Specified Condition
    Battery position (+) → Terminal I10-1 (MR)
    Battery negative (-) → Terminal I10-2 (MF)
    		Forward position (A)
    		Moves from (A) to retracted position (E)
    Battery position (+) → Terminal I10-2 (MF)
    Battery negative (-) → Terminal I10-1 (MR)
    		Forward position (A)
    		Does not move
    Battery position (+) → Terminal I10-1 (MR)
    Battery negative (-) → Terminal I10-2 (MF)
    		Position between forward position (A) and driving position (C)
    		Moves from (B) to retracted position (E)
    Battery position (+) → Terminal I10-2 (MF)
    Battery negative (-) → Terminal I10-1 (MR)
    		Position between forward position (A) and driving position (C)
    		Moves from (B) to forward position (A)
    Battery position (+) → Terminal I10-1 (MR)
    Battery negative (-) → Terminal I10-2 (MF)
    		Driving position (C)
    		Moves from (C) to retracted position (E)
    Battery position (+) → Terminal I10-2 (MF)
    Battery negative (-) → Terminal I10-1 (MR)
    		Driving position (C)
    		Does not move
    Battery position (+) → Terminal I10-1 (MR)
    Battery negative (-) → Terminal I10-2 (MF)
    		Position between driving position (C) and retracted position (E)
    		Moves from (D) to retracted position (E)
    Battery position (+) → Terminal I10-2 (MF)
    Battery negative (-) → Terminal I10-1 (MR)
    		Position between driving position (C) and retracted position (E)
    		Moves from (D) to driving position (C)
    Battery position (+) → Terminal I10-1 (MR)
    Battery negative (-) → Terminal I10-2 (MF)
    		Retracted position (E)
    		Does not move
    Battery position (+) → Terminal I10-2 (MF)
    Battery negative (-) → Terminal I10-1 (MR)
    		Retracted position (E)
    		Moves from (E) to driving position (C)
    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.


    Corolla. Zre142 Aze141.Mirror (Ext).Power Mirror Control System.Outer Rear View Mirror Inspection

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → I10-5 (+)
      Battery negative (-) → I10-4 (-)
      		Mirror surface temperature becomes higher
      Text in Illustration
      *a
      		Component without harness connected
      (Mirror Sub-assembly LH)
      If the result is not as specified, replace the mirror sub-assembly LH.