REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (w/o Front No. 2 Speaker)
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (w/ Front No. 2 Speaker)
Front Door Belt Moulding -- Removal |
- HINT:
- Use the same procedure for the RH side and LH side.
- The procedure listed below is for the LH side.
| 1. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
Using a clip remover, remove the snap ring.
 |
Remove the front door window regulator handle assembly and front door regulator inside handle plate.
| 2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel.
 |
| 3. REMOVE FRONT ARMREST UPPER BASE PANEL (w/o Power Window) |
Using a moulding remover, disengage the 2 clips and 6 claws, and remove the front armrest upper base panel.
 |
w/ Power Door Lock:
Disconnect the connector.
| 4. REMOVE FRONT ARMREST UPPER BASE PANEL (w/ Power Window) |
Using a moulding remover, disengage the 2 clips and 6 claws.
 |
Disconnect the connector and remove the front armrest upper base panel.
| 5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and disconnect the door armrest cap.
 |
Remove the 2 screws.
 |
Using a clip remover, disengage the 10 clips.
 |
Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.
Disengage the 2 claws and disconnect the front door inside handle sub-assembly.
 |
| 6. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.
 |
| 7. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (w/o Front No. 2 Speaker) |
Disengage the clip and clamp, and remove the front door lower frame bracket garnish.
 |
| 8. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (w/ Front No. 2 Speaker) |
Disengage the clip and clamp.
 |
Disconnect the connector and remove the front door lower frame bracket garnish.
| 9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
Remove the front door inner glass weatherstrip from the front door panel.
 |
| 10. REMOVE FRONT DOOR TRIM BRACKET |
Remove the 2 screws and the front door trim bracket.
 |
| 11. REMOVE FRONT DOOR SERVICE HOLE COVER |
w/ Power door lock:
Disconnect the connector.
Remove the front door service hole cover.
- HINT:
- Remove any remaining butyl tape from the door.
 |
| 12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER |
Disconnect the clamp and connector.
 |
Remove the 3 bolts.
Disengage the claw and remove the outer rear view mirror assembly with cover.
| 13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY (w/o Power Window) |
Install the front door window regulator handle assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Remove the front door window regulator handle assembly.
Remove the 2 bolts.
- NOTICE:
- After the bolts are removed, do not allow the door glass to fall.
 |
Remove the front door glass sub-assembly as shown in the illustration.
- NOTICE:
- Do not damage the door glass.
 |
| 14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY (w/ Power Window) |
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
Remove the 2 bolts.
- NOTICE:
- After the bolts are removed, do not allow the door glass to fall.
|
Remove the front door glass sub-assembly as shown in the illustration.
- NOTICE:
- Do not damage the door glass.
|
| 15. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY |
Put protective tape around the front door belt moulding assembly.
 |
Using a screwdriver with its tip taped, disengage the 5 claws from the inside of the door.
Using a moulding remover, disengage the clip and remove the front door belt moulding assembly.