Dtc P0630 Vin Not Programmed Or Mismatch - Ecm / Pcm
MONITOR DESCRIPTION
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
COMPONENT OPERATING RANGE
CONFIRMATION DRIVING PATTERN
INSPECTION PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0630)
INPUT VIN
DTC P0630 VIN not Programmed or Mismatch - ECM / PCM |
MONITOR DESCRIPTION
DTC P0630 is set when the Vehicle Identification Number (VIN) is not stored in the Engine Control Module (ECM) or the input VIN is not accurate. Input the VIN with the Techstream.DTC No.
| DTC Detection Condition
| Trouble Area
|
P0630
| When either condition below is met (1 trip detection logic):
- VIN not stored in ECM
- Input VIN in ECM not accurate
| ECM
|
MONITOR STRATEGY
Related DTCs
| P0630: VIN not programmed
|
Required Sensors/Components (Main)
| ECM
|
Required Sensors/Components (Related)
| -
|
Frequency of Operation
| Continuous
|
Duration
| 0.325 seconds
|
MIL Operation
| Immediate
|
Sequence of Operation
| None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not stored
| None
|
Battery voltage
| 8 V or more
|
Ignition switch
| ON
|
Starter
| Off
|
TYPICAL MALFUNCTION THRESHOLDS
COMPONENT OPERATING RANGE
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (COROLLA_ZRE142 RM000000PDK0ZAX.html).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the Techstream on.
- Wait 5 seconds or more.
- Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
- Read the pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P0630.
- Check the DTC judgment result.
Techstream Display
| Description
|
NORMAL
| - DTC judgment completed
- System normal
|
ABNORMAL
| - DTC judgment completed
- System abnormal
|
INCOMPLETE
| - DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
|
N/A
| - Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (COROLLA_ZRE142 RM000000PDK0ZAX.html).
- HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0630) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
- Result:
Result
| Proceed to
|
DTC P0630 is output
| A
|
DTC P0630 and other DTCs are output
| B
|
- NOTICE:
- If P0630 is set, the VIN must be input to the ECM using the Techstream. However, all DTCs are cleared automatically by the Techstream when inputting the VIN. If DTCs other than P0630 are set, check them first.
- HINT:
- If any DTCs other than P0630 are output, troubleshoot those DTCs first.
Input the VIN (COROLLA_ZRE142 RM000000PDT0AMX.html).