Vehicle Stability Control System Dtc Check / Clear

Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40

  1. DTC CHECK/CLEAR (INTELLIGENT TESTER)

  1. DTC CHECK/CLEAR (SST CHECK WIRE)

  1. END OF DTC CHECK/CLEAR

Vehicle Stability Control System -- Dtc Check / Clear



DTC CHECK/CLEAR (INTELLIGENT TESTER)


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System.Vehicle Stability Control System Dtc Check / Clear

  1. Check the DTC.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Read the DTCs following the prompts on the tester screen.

  2. Clear the DTC.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Operate the intelligent tester to clear the codes.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

DTC CHECK/CLEAR (SST CHECK WIRE)


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System.Vehicle Stability Control System Dtc Check / Clear

  1. Check the DTC.

    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040

    2. Turn the ignition switch on (IG).

    3. Observe the blinking pattern of the ABS warning and SLIP indicator lights and/or read the multi information display in order to identify the DTC.

      HINT:
      If no code appears, inspect the TC and CG terminal circuit, and ABS warning and SLIP indicator light circuits.
      Trouble Area
      		See procedure
      TC and CG terminal circuit
      		CAMRY_ACV40 RM000000XIU05MX.html or CAMRY_ACV40 RM000000XIQ054X.html
      SLIP indicator light circuit
      		CAMRY_ACV40 RM000000YHI041X.html or CAMRY_ACV40 RM000000YHJ041X.html


    4. As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21 for ABS warning and SLIP indicator lights and/or display of the normal system code and trouble code 43 for the VSC on the multi information display.


      Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System.Vehicle Stability Control System Dtc Check / Clear

    5. The codes are explained in the code table (CAMRY_ACV40 RM000000XHU03XX.html).

    6. After completing the check, disconnect terminals TC and CG of the DLC3, and turn off the display.
      If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



  2. Clear the DTC.



      Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System.Vehicle Stability Control System Dtc Check / Clear

    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040

    2. Turn the ignition switch on (IG).



      3. Camry. Acv40 Gsv40

    3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    4. Check that the warning light or multi information display indicates the normal system code.

    5. Remove the SST from the terminals of the DLC3.

      HINT:
      Clearing the DTCs cannot be performed by disconnecting the battery terminal or the ECU-IG NO. 2 fuse.

END OF DTC CHECK/CLEAR

  1. Turn the ignition switch on (IG).

  2. Check that the ABS warning and SLIP indicator lights go off within approximately 3 seconds.