Cruise Control System System Description

Cruise Control System. Camry. Acv40 Gsv40
Cruise Control. Camry. Acv40 Gsv40

  1. CRUISE CONTROL SYSTEM

  1. LIMIT CONTROL

  1. OPERATION OF CRUISE CONTROL

  1. AUTO CANCEL (FAIL-SAFE)

Cruise Control System -- System Description



CRUISE CONTROL SYSTEM
This system is controlled by the ECM, and is activated by the throttle position sensor and motor. The ECM controls the following functions: ON-OFF, - (COAST)/SET, + (ACCEL)/RES (RESUME), CANCEL, vehicle speed operation, motor output control, and overdrive control.
HINT:
Overdrive control is equipped on only vehicles with an automatic transaxle.
  1. The ECM compares the driving vehicle speed from the speed sensor with the stored vehicle speed set through the cruise control main switch. The ECM instructs the throttle valve motor of the throttle body assembly to close the valve when the driving speed is greater than the stored speed, and instructs it to open the valve when the driving speed is less than the stored speed.
  2. The ECM receives signals such as ON-OFF, - (COAST)/SET, + (ACCEL)/RES (RESUME), and CANCEL from the cruise control main switch and executes the command.
  3. The ECM illuminates the combination meter's CRUISE main indicator light when it receives a cruise control main switch ON signal.
  4. The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives a stop light switch signal.
  5. On vehicles with an automatic transaxle, the ECM cancels the cruise control system when the shift lever is moved from the D to the N position or the transmission is shifted to the 3rd, 2nd, or 1st gear with the shift lever in the S position, and the ECM receives a park/neutral position switch signal.
  6. In manual transaxle vehicle, the ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives a clutch switch signal.

LIMIT CONTROL

  1. Low speed limit
    The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. Cruise control operation will be automatically canceled but the stored vehicle speed will be retained when the vehicle speed drops below the low speed limit 40 km/h (25 mph) while the cruise control is in operation.

  2. High speed limit
    The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, + (ACCEL)/RES (RESUME) cannot be used to increase speed beyond the high speed limit.


OPERATION OF CRUISE CONTROL
The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it.

  1. SET CONTROL
    The vehicle speed is stored and constant speed control is maintained when pushing the cruise control main switch to - (COAST)/SET while driving with the main switch on (the CRUISE main indicator light is on), and the vehicle speed is within the set speed range (between the low and high speed limits).

  2. - (COAST) CONTROL
    When the cruise control main switch is set to - (COAST)/SET and held in that position while the cruise control system is operating, the ECM sends a "throttle valve opening angle 0°" demand signal to the cruise control system. Then the vehicle speed, when the cruise control main switch is released, is stored and maintained.

    HINT:
    An actual throttle valve opening angle of 0° is not possible due to the idle speed control, etc.

  3. TAP-DOWN CONTROL
    When tapping down the cruise control main switch to - (COAST)/SET (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control main switch is released from - (COAST)/SET and the difference between the driving and stored vehicle speed is more than 5 km/h (3 mph), the driving vehicle speed is stored and constant speed control is maintained.

  4. ACCELERATION CONTROL
    The throttle valve motor of the throttle body assembly is instructed by the ECM to open the throttle valve when + (ACCEL)/RES (RESUME) on the cruise control main switch is pressed and held while the cruise control system is in operation. When the cruise control main switch is released from + (ACCEL)/RES (RESUME), the vehicle speed is stored and the vehicle is controlled at a constant speed.

  5. TAP-UP CONTROL
    When tapping up the cruise control main switch to + (ACCEL)/RES (RESUME) (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (approximately 3 mph), the stored vehicle speed will not be changed.

  6. RESUME CONTROL
    If cruise control operation was canceled with the stop light switch or the CANCEL switch, and if driving speed is within the limit range, pushing the cruise control main switch to + (ACCEL)/RES (RESUME) restores vehicle speed memorized at the time of cancellation, and maintains constant speed control.

  7. MANUAL CANCEL CONTROL
    Performing any of the following cancels the cruise control system while in operation (the stored vehicle speed in the ECM is maintained).

    1. Pulling the cruise control main switch to CANCEL
    2. Depressing the brake pedal
    3. Depressing the clutch pedal (M/T)
    4. The shift lever is moved from the D to the N position or the transmission is shifted to the 3rd, 2nd, or 1st gear with the shift lever in the S position (A/T).
    5. Turning the cruise control main switch off (the stored vehicle speed in the ECM is not maintained).

AUTO CANCEL (FAIL-SAFE)
This system has an automatic cancellation function (fail-safe) (CAMRY_ACV40 RM000000ST100WX.html).