Cruise Control System Cruise Control Switch Circuit

Cruise Control System. Camry. Acv40 Gsv40
Cruise Control. Camry. Acv40 Gsv40

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE ON INTELLIGENT TESTER

INSPECT CRUISE CONTROL MAIN SWITCH

CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)

CHECK SPIRAL CABLE

CHECK WIRE HARNESS (SPIRAL CABLE - ECM AND BODY GROUND)

CRUISE CONTROL SYSTEM - Cruise Control Switch Circuit


DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM


Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit


INSPECTION PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Check the DATA LIST for proper functioning of the cruise control main switch.

    ECM (Cruise control):
    Item
    		Measurement Item/Display (Range)
    		Normal Condition
    		Diagnostic Note
    Main SW (Main)
    		Main switch signal (Main CPU)/ON or OFF
    		ON: Cruise control main switch on
    OFF: Cruise control main switch off
    		-
    Cancel SW
    		CANCEL switch signal/ON or OFF
    		ON: CANCEL switch on
    OFF: CANCEL switch off
    		-
    SET / COAST SW
    		SET / COAST switch signal/ON or OFF
    		ON: - (COAST)/SET switch on
    OFF: - (COAST)/SET switch off
    		-
    RES / ACC SW
    		RES / ACC switch signal/ON or OFF
    		ON: + (ACCEL)/RES (RESUME) switch on
    OFF: + (ACCEL)/RES (RESUME) switch off
    		-
    Main SW (Sub)
    		Main switch signal (Sub CPU) / ON or OFF
    		ON: Cruise control main switch ON
    OFF: Cruise control main switch OFF
    		-
    OK:
    When the cruise control main switch is operated, the display changes as shown above.
    Result
    Result
    		Proceed to
    OK
    		A
    NG (All items are defective)
    		B
    NG (1 to 4 items are defective)
    		C


A
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE CRUISE CONTROL MAIN SWITCH
B


2.INSPECT CRUISE CONTROL MAIN SWITCH

  1. Remove the cruise control main switch (CAMRY_ACV40 RM000000VQ302SX.html).



  1. Measure the resistance according to the value(s) in the table below.


    Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit


Standard resistance:

Tester Connection
Switch Condition
Specified Condition
A-1 (CCS) - A-3 (ECC)
Neutral
10 kΩ or higher
+ (ACCEL)/RES (RESUME)
216 to 264 Ω
- (COAST)/SET
567 to 693 Ω
CANCEL
1,386 to 1,694 Ω
Main Switch on
Below 1 Ω


NG
REPLACE CRUISE CONTROL MAIN SWITCH
OK


3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit

  1. Disconnect the b1 connector from the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    		Condition
    		Specified condition
    A-1 - b1-3
    		Always
    		Below 1 Ω
    A-3 - b1-4
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SPIRAL CABLE
Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit
NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.
HINT:
  1. Removal (CAMRY_ACV40 RM000000UWD04BX.html)
  2. Installation (CAMRY_ACV40 RM000000UWA04BX.html)

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Spiral Cable Position
    		Specified Condition
    b1-3 - E18-1 (CCS)
    		Center
    		Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    b1-4 - E18-2 (ECC)
    		Center
    		Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
HINT:
The spiral cable makes a maximum of approximately 5 rotations.


NG
REPLACE SPIRAL CABLE
OK


5.CHECK WIRE HARNESS (SPIRAL CABLE - ECM AND BODY GROUND)


    Camry. Acv40 Gsv40.Cruise Control.Cruise Control System.Cruise Control System Cruise Control Switch Circuit

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E18-1 - A55-40 (CCS)*1
    E18-1 - A24-40 (CCS)*2
    		Always
    		Below 1 Ω
    A55-40 (CCS) - Body ground*1
    A24-40 (CCS) - Body ground*2
    		Always
    		10 kΩ or higher
    E18-2 (ECC) - Body ground
    		Always
    		Below 1 Ω
    HINT:
    *1: 2GR-FE (LHD)
    *2: 2AZ-FE, 2GR-FE (RHD)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM