2Gr-Fe Engine Control System. Dtc P2120 Throttle / Pedal Position Sensor / Switch D Circuit

This ETCS (Electronic Throttle Control System) does not use a throttle cable.
The Accelerator Pedal Position (APP) sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

Camry. Acv40 Gsv40.2Gr-Fe Engine Control System.Sfi System.
Dtc
P2120 Throttle / Pedal Position Sensor / Switch D Circuit

DTC No.	DTC Detection Condition	Trouble Area
P2120	VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)	Accelerator Pedal Position (APP) sensor ECM
P2122	VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic)	APP sensor Open in VCP1 circuit Open or ground short in VPA circuit ECM
P2123	VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)	APP sensor Open in EPA circuit ECM
P2125	VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)	APP sensor ECM
P2127	VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic)	APP sensor Open in VCP2 circuit Open or ground short in VPA2 circuit ECM
P2128	Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more (b) VPA is between 0.4 V and 3.45 V	APP sensor Open in EPA2 circuit ECM
P2138	Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less	Short between VPA and VPA2 circuits APP sensor ECM

HINT:

When any of these DTCs are set, check the APP sensor voltage by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

Trouble Area	ACCEL POS #1 When AP Released	ACCEL POS #2 When AP Released	ACCEL POS #1 When AP Depressed	ACCEL POS #2 When AP Depressed
VCP circuit open	0 to 0.4 V	0 to 1.2 V	0 to 0.4 V	0 to 1.2 V
Open or ground short in VPA circuit	0 to 0.4 V	1.2 to 2.0 V	0 to 0.4 V	3.4 to 5.0 V
Open or ground short in VPA2 circuit	0.5 to 1.1 V	0 to 0.2 V	2.6 to 4.5 V	0 to 0.2 V
EPA circuit open	4.5 to 5.0 V	4.5 to 5.0 V	4.5 to 5.0 V	4.5 to 5.0 V
Normal condition	0.5 to 1.1 V	1.2 to 2.0 V	2.6 to 4.5 V	3.4 to 5.0 V

HINT:

Accelerator pedal positions are expressed as voltages.
AP denotes Accelerator Pedal.

FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (CAMRY_ACV40 RM000000PDS01FX.html).

These DTCs relate to the Accelerator Pedal Position (APP) sensor.

1.READ VALUE USING INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to the ON position and turn the tester on.

Enter the following menus: Powertrain / Engine / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

Read the value displayed on the tester.
Standard voltage:
Accelerator Pedal Operation
ACCEL POS #1
(AP#1)
ACCEL POS #2
(AP#2)
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.0 V

Go to step 5

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

Disconnect the A17 Accelerator Pedal Position (APP) sensor connector.

Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):

RHD:

Tester Connection	Specified Condition
VPA (A17-6) - VPA (A24-55)	Below 1 Ω
EPA (A17-5) - EPA (A24-59)	Below 1 Ω
VCPA (A17-4) - VCPA (A24-57)	Below 1 Ω
VPA2 (A17-3) - VPA2 (A24-56)	Below 1 Ω
EPA2 (A17-2) - EPA2 (A24-60)	Below 1 Ω
VCP2 (A17-1) - VCP2 (A24-58)	Below 1 Ω

LHD:

Tester Connection	Specified Condition
VPA (A17-6) - VPA (A55-55)	Below 1 Ω
EPA (A17-5) - EPA (A55-59)	Below 1 Ω
VCPA (A17-4) - VCPA (A55-57)	Below 1 Ω
VPA2 (A17-3) - VPA2 (A55-56)	Below 1 Ω
EPA2 (A17-2) - EPA2 (A55-60)	Below 1 Ω
VCP2 (A17-1) - VCP2 (A55-58)	Below 1 Ω

Standard resistance (Check for short):

RHD:

Tester Connection	Specified Condition
VPA (A17-6) or VPA (A24-55) - Body ground	10 kΩ or higher
EPA (A17-5) or EPA (A24-59) - Body ground	10 kΩ or higher
VCPA (A17-4) or VCPA (A24-57) - Body ground	10 kΩ or higher
VPA2 (A17-3) or VPA2 (A24-56) - Body ground	10 kΩ or higher
EPA2 (A17-2) or EPA2 (A24-60) - Body ground	10 kΩ or higher
VCP2 (A17-1) or VCP2 (A24-58) - Body ground	10 kΩ or higher

LHD:

Tester Connection	Specified Condition
VPA (A17-6) or VPA (A55-55) - Body ground	10 kΩ or higher
EPA (A17-5) or EPA (A55-59) - Body ground	10 kΩ or higher
VCPA (A17-4) or VCPA (A55-57) - Body ground	10 kΩ or higher
VPA2 (A17-3) or VPA2 (A55-56) - Body ground	10 kΩ or higher
EPA2 (A17-2) or EPA2 (A55-60) - Body ground	10 kΩ or higher
VCP2 (A17-1) or VCP2 (A55-58) - Body ground	10 kΩ or higher

Reconnect the APP sensor connector.

Reconnect the ECM connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.INSPECT ACCELERATOR POSITION SENSOR (VCPA AND VCP2 VOLTAGE)

Disconnect the A17 APP sensor connector.

Turn the ignition switch to the ON position.

Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Specified Condition
VCPA (A17-4) - EPA (A17-5)
4.5 to 5.0 V
VCP2 (A17-1) - EPA2 (A17-2)
4.5 to 5.0 V

Reconnect the APP sensor connector.

REPLACE ECM (CAMRY_ACV40 RM0000022NT00VX.html)

OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to the ON position and turn the tester on.

Clear the DTCs (CAMRY_ACV40 RM000000PDK0D6X.html).

Start the engine.

Allow the engine to idle for 15 seconds.

Enter the following menus: Powertrain / Engine / DTC.

Read the DTCs.

Result:

Display (DTC Output)
Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138
A
No output
B

SYSTEM IS OK

REPLACE ECM (CAMRY_ACV40 RM0000022NT00VX.html)

Accelerator Pedal Operation	ACCEL POS #1 (AP#1)	ACCEL POS #2 (AP#2)
Released	0.5 to 1.1 V	1.2 to 2.0 V
Depressed	2.6 to 4.5 V	3.4 to 5.0 V

Tester Connection	Specified Condition
VCPA (A17-4) - EPA (A17-5)	4.5 to 5.0 V
VCP2 (A17-1) - EPA2 (A17-2)	4.5 to 5.0 V

Display (DTC Output)	Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138	A
No output	B