ЗАДАЮЩАЯ ШЕСТЕРНЯ - ПОВТОРНАЯ СБОРКА

Using SST and a press, install a new radial ball bearing (inner race) to the counter gear.

• SST
• 09316-60011(09316-00041)
  09950-60010(09951-00540)

Select a new snap ring that will allow minimal axial play.

• Standard clearance:
• 0.1 mm (0.00394 in.) or less

• Standard Snap Ring:

• Part No.	Mark	Thickness
  90520-31015	A	2.35 to 2.40 mm (0.0925 to 0.0945 in.)
  90520-31016	B	2.40 to 2.45 mm (0.0945 to 0.0965 in.)
  90520-31017	C	2.45 to 2.50 mm (0.0965 to 0.0984 in.)
  90520-31018	D	2.50 to 2.55 mm (0.0984 to 0.1004 in.)
  90520-31019	E	2.55 to 2.60 mm (0.1004 to 0.1024 in.)
  90520-31020	F	2.60 to 2.65 mm (0.1024 to 0.1043 in.)
  90520-31021	G	2.65 to 2.70 mm (0.1043 to 0.1063 in.)
  90520-31022	H	2.70 to 2.75 mm (0.1063 to 0.1083 in.)
  90520-31023	J	2.75 to 2.80 mm (0.1083 to 0.1102 in.)
  90520-31024	K	2.80 to 2.85 mm (0.1102 to 0.1122 in.)
  90520-31025	L	2.85 to 2.90 mm (0.1122 to 0.1142 in.)
  90520-31033	M	2.90 to 2.95 mm (0.1142 to 0.1161 in.)

Using a snap ring expander, install the snap ring to the counter gear.

Apply a light coat of gear oil to the sleeve and hub.

Install the clutch hub to the clutch hub sleeve.

Install one of the balls to each shifting key.

Install one of the springs to each shifting key.

Install the shifting keys with balls and springs to the No. 1 clutch hub.

• ПРИМЕЧАНИЕ:

• Be careful to prevent the balls from flying off.

Coat the 2nd gear needle roller bearing with gear oil, and then install it to the counter gear.

Coat the counter shaft 2nd speed gear with gear oil, and then install it to the counter gear.

Coat the No. 1 synchronizer ring set with gear oil, and then install it to the counter gear.

Using SST and a press, install the No. 1 transmission clutch hub to the counter gear.

• SST
• 09316-60011

• УКАЗАНИЕ:

• Align the groove of the clutch hub with the protrusion of the synchronizer ring.

Check that the gear and synchronizer ring move smoothly.

Select a new snap ring that will allow minimal axial play.

• Standard clearance:
• 0.1 mm (0.00394 in.) or less

• Standard Snap Ring:

• Part No.	Mark	Thickness
  90520-45013	A	2.28 to 2.33 mm (0.0898 to 0.0917 in.)
  90520-45014	B	2.33 to 2.38 mm (0.0917 to 0.0937 in.)
  90520-45015	C	2.38 to 2.43 mm (0.0937 to 0.0957 in.)
  90520-45016	D	2.43 to 2.48 mm (0.0957 to 0.0976 in.)
  90520-45017	E	2.48 to 2.53 mm (0.0976 to 0.0996 in.)
  90520-45018	F	2.53 to 2.58 mm (0.0996 to 0.1016 in.)
  90520-45019	G	2.58 to 2.63 mm (0.1016 to 0.1035 in.)

Using a snap ring expander, install the snap ring to the counter gear.

Coat the No. 1 synchronizer ring set with gear oil, and then install it to the counter gear.

Coat the 1st gear needle roller bearing with gear oil, and then install it to the counter gear.

Coat the counter shaft 1st speed gear with gear oil and install it to the counter gear.

Using SST and a press, install the reverse gear spline piece.

• SST
• 09309-37010

Install the ball to the counter gear.

Coat the No. 4 synchronizer ring with gear oil and install it to the counter gear.

Coat the reverse gear needle roller bearing with gear oil and install it to the counter gear.

Install the key spring and 2 shifting keys to the reverse gear.

• УКАЗАНИЕ:

Install the hub sleeve to the reverse gear.

Coat the countershaft reverse gear with gear oil, and then install it to the counter gear.

Align the groove of the reverse gear bearing race inner with the ball and install the reverse gear bearing race inner.

Using SST and a press, install the counter gear front bearing or roller to the counter gear.

• SST
• 09608-06041

• УКАЗАНИЕ:

• Make sure that the groove of the bearing faces the correct direction as shown in the illustration.

Select a new snap ring that will allow minimal axial play.

• Standard clearance:
• 0.1 mm (0.00394 in.) or less

• Standard Snap Ring:

• Part No.	Mark	Thickness
  90520-31015	A	2.35 to 2.40 mm (0.0925 to 0.0945 in.)
  90520-31016	B	2.40 to 2.45 mm (0.0945 to 0.0965 in.)
  90520-31017	C	2.45 to 2.50 mm (0.0965 to 0.0984 in.)
  90520-31018	D	2.50 to 2.55 mm (0.0984 to 0.1004 in.)
  90520-31019	E	2.55 to 2.60 mm (0.1004 to 0.1024 in.)
  90520-31020	F	2.60 to 2.65 mm (0.1024 to 0.1043 in.)
  90520-31021	G	2.65 to 2.70 mm (0.1043 to 0.1063 in.)
  90520-31022	H	2.70 to 2.75 mm (0.1063 to 0.1083 in.)
  90520-31023	J	2.75 to 2.80 mm (0.1083 to 0.1102 in.)
  90520-31024	K	2.80 to 2.85 mm (0.1102 to 0.1122 in.)
  90520-31025	L	2.85 to 2.90 mm (0.1122 to 0.1142 in.)
  0520-31033	M	2.90 to 2.95 mm (0.1142 to 0.1161 in.)

Using a snap ring expander, install the snap ring to the counter gear.

Using a feeler gauge, measure the reverse gear thrust clearance.

• Standard clearance:
• 0.125 to 0.375 mm (0.00493 to 0.0148 in.)

If the clearance is outside the specification, replace the gear, spline piece or bearing race.

• УКАЗАНИЕ:

• Replace the part or parts determined to be the most likely cause of the problem.

Using a dial indicator, measure the 1st gear thrust clearance.

• Standard clearance:
• 0.10 to 0.43 mm (0.00394 to 0.0169 in.)

If the clearance is outside the specification, replace the gear, clutch hub, spline piece or counter gear.

• УКАЗАНИЕ:

• Replace the part or parts determined to be the most likely cause of the problem.

Using a dial indicator, measure the 2nd gear thrust clearance.

• Standard clearance:
• 0.10 to 0.43 mm (0.00394 to 0.0169 in.)

If the clearance is outside the specification, replace the gear, clutch hub or counter gear.

• УКАЗАНИЕ:

• Replace the part or parts determined to be the most likely cause of the problem.

Using a dial indicator, measure the reverse gear radial clearance.

• Standard clearance:
• 0.015 to 0.065 mm (0.000591 to 0.00255 in.)

If the clearance is outside the specification, replace the reverse gear needle roller bearing or shaft.

• УКАЗАНИЕ:

• Replace the part or parts determined to be the most likely cause of the problem.

Using a dial indicator, measure the 1st gear radial clearance.

• Standard clearance:
• 0.015 to 0.067 mm (0.000591 to 0.00263 in.)

If the clearance is outside the specification, replace the 1st gear needle roller bearing or shaft.

• УКАЗАНИЕ:

• Replace the part or parts determined to be the most likely cause of the problem.

Using a dial indicator, measure the 2nd gear radial clearance.

• Standard clearance:
• 0.015 to 0.067 mm (0.000591 to 0.00263 in.)

If the clearance is outside the specification, replace the 2nd gear needle roller bearing or shaft.