Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - THEFT DETERRENT / KEYLESS ENTRY
THEFT DETERRENT SYSTEM (w/ Entry and Start System) - OPERATION CHECK
- HINT:
OUTLINE OF THEFT DETERRENT SYSTEM |
When the theft deterrent system detects that the vehicle is being tampered with, the horns sound and lights flash continuously. For vehicles with a siren, the theft warning siren (self power siren) sounds simultaneously.
The system has active arming mode (refer to "Active Arming Mode").
Active arming mode has 4 states: disarmed state, arming preparation state, armed state and alarm sounding state.
Disarmed state:
Arming preparation state:
Armed state:
Alarm sounding state:
Alarm Method | Hazard Warning Light | Blinking (cycle of flasher relay) |
Vehicle Horn | Sounding (cycle of 0.4 seconds) | |
Security Horn*1 | Sounding (cycle of 0.4 seconds) | |
Headlight*1 | Flashing | |
Taillight*1 | Flashing | |
Room Light | Illuminating | |
Theft Warning Siren (Self Power Siren)*2 | Sounding (cycle of 0.4 seconds) | |
Security Indicator | Illuminating | |
Alarm Time | 30 +/-5 seconds |
- HINT:
ACTIVE ARMING MODE |
- HINT:
System State | State Switching Condition | Transfer to |
1. Disarmed state | Perform one of following, and system will go on to "Arming preparation state": With all doors and engine hood closed, lock all doors by wireless operation. With all doors and engine hood closed, lock all doors using mechanical key.*1 With any door or engine hood open, lock all doors and close all doors and engine hood.*1 | 2. Arming preparation state |
2. Arming preparation state | Perform one of following, and system will go on to "Disarmed state": Unlock all doors by wireless operation. Unlock all doors using mechanical key.*1 Unlock door. Open engine hood. With brake pedal depressed, put and hold key 10 mm (0.393 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn engine switch on (ACC) or on (IG). Reconnect battery. | 1. Disarmed state |
Perform one of following, and system will go on to "Armed state": Allow 30 (+/-1.5) seconds to elapse. | 3. Armed state | |
3. Armed State | Perform one of following, and system will go on to "Disarmed state": Unlock all doors by wireless operation. Unlock all doors using mechanical key.*1 With brake pedal depressed, put and hold key 10 mm (0.393 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn engine switch on (IG). | 1. Disarmed state |
Perform one of following, and system will go on to "Alarm sounding state": Open engine hood. Open door. Unlock door without using wireless operation.*2 Unlock door without using mechanical key.*1 Disconnect and reconnect battery negative (-) cable.*3 Force engine ignition system to turn on without proper engine start method. Intrusion sensor detects movement within vehicle.*4 | 4. Alarm sounding state | |
4. Alarm sounding state | Perform one of following, and system will go on to "Disarmed state": Unlock all doors using wireless operation.*2 Unlock all doors using mechanical key.*1 With brake pedal depressed, put and hold key 10 mm (0.393 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn engine switch ON (IG). | 1. Disarmed state |
Perform one of following, and system will go on to "Armed state": Allow 30 (+/-5) seconds to elapse. | 3. Armed state (alarm stops sounding) |
- HINT:
- *1: w/ Security Horn
- *2: w/ Theft Warning Siren (Self Power Siren)
- *3: For vehicles with a theft warning siren (self power siren), the siren begins to sound as soon as the battery cable is disconnected.
- *4: w/ Intrusion sensor
FORCED DOOR LOCK CONTROL |
The forced door lock control also helps to prevent the vehicle from being tampered with. When a door is unlocked and the alarm starts, the door is forced to lock by a forced door lock signal.
Conditions that force the doors to lock:
PANIC ALARM CONTROL (w/ Panic Switch) |
The panic alarm control activates the panic alarm when the wireless transmitter panic switch is pressed. The panic alarm control operates independently from the change of the theft deterrent system alarm control from the armed state to the alarm sounding state.
Conditions that cause the panic alarm control to set off the panic alarm:
The panic alarm is activated when the panic switch on the wireless transmitter is pressed and held for 1.0 seconds or more under the following conditions.
Conditions that cause the panic alarm control to shut off the alarm:
The panic alarm is deactivated when any of the following conditions is fulfilled during panic alarm operation.
Conditions for canceling the panic alarm are the same as for the alarm control.
- HINT:
- For more information about active mode, refer to "Active Arming Mode".
SECURITY INDICATOR OUTPUT |
The security indicator turns on and off based on output signals from the certification ECU (smart key ECU assembly). However, in some cases, the actual status of the security indicator is different from the output signals of the certification ECU (smart key ECU assembly).
State of Theft Deterrent System | Security Indicator | |
Output Signals from ECU | Actual Lighting Condition | |
Disarmed state | Off | Off (Immobiliser system not set) Blinking (Immobiliser system set) |
Arming preparation state | On | On |
Armed state | Off | Blinking |
Alarm sounding state | On | On |
Time | Security Indicator |
0.125 seconds | On |
1.875 seconds | Off |
- HINT:
- When the immobiliser system is set, the security indicator blinks during the disarmed state and the armed state due to the output signals from the immobiliser system.