Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - INTERIOR PANELS / TRIM
ROOF HEADLINING (w/o Sliding Roof) - INSTALLATION
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart ().
| 1. INSTALL SIDE TRIM BOX |
Install the side trim box with the 9 screws.
| 2. INSTALL SIDE TRIM BOX COVER |
Install the side trim box cover.
| 3. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH |
Install the quarter trim lid.
| 4. INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type) |
Attach the 6 clips to install the quarter trim cover.
| 5. INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 6. INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
Attach the 6 clips to install the rear No. 2 seat cover bezel.
| 7. INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the rear No. 2 seat cover bezel.
| 8. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
Attach the 4 claws to install the seat lock control lever.
| 9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 10. INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater) |
Attach the 4 claws to install the cover.
| 11. INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater) |
- HINT:
- Use the same procedures described for the LH side.
| 12. INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater) |
Attach the 4 claws to install the cover.
| 13. INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater) |
Attach the 4 claws to install the cover.
Install the duct with the 6 screws.
| 14. INSTALL TONNEAU COVER HANGER LH (w/ Tonneau Cover) |
Install the tonneau cover hanger and rear quarter trim base with the 2 screws.
| 15. INSTALL TONNEAU COVER HANGER RH (w/ Tonneau Cover) |
- HINT:
- Use the same procedures described for the LH side.
| 16. INSTALL TONNEAU COVER HOLDER BRACKET LH (w/ Tonneau Cover) |
Attach the 3 claws to install the tonneau cover holder bracket.
Install the front quarter trim base with the 3 screws and then install the remaining 5 screws.
| 17. INSTALL TONNEAU COVER HOLDER BRACKET RH (w/ Tonneau Cover) |
- HINT:
- Use the same procedures described for the LH side.
| 18. INSTALL NO. 2 CUP HOLDER |
Attach the 3 claws to install the cup holder.
Install the 5 screws.
| 19. INSTALL NO. 1 CUP HOLDER |
Attach the 3 claws to install the cup holder.
Install the 5 screws.
| 20. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH |
Attach the 4 claws to install the quarter trim cover.
Install the 7 screws.
w/ Rear Heater:
Install the duct with the 8 screws.
| 21. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH |
Attach the 4 claws to install the quarter trim cover.
Install the 7 screws.
| 22. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH |
Install the hanger with 2 new spring nuts.
| 23. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH |
- HINT:
- Use the same procedures described for the LH side.
| 24. INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure to install the hanger on the other side.
Install the hanger with 2 new spring nuts.
| 25. INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
Attach the 7 claws to install the cover.
| 26. INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 27. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
Attach the 6 claws to install the plate.
| 28. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 29. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
Slide the plate in the direction shown in the illustration and attach the 6 claws to install the plate.
| 30. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 31. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH |
Attach the 3 clips to install the rear door scuff plate outside.
| 32. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH |
- HINT:
- Use the same procedures described for the LH side.
| 33. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH |
Attach the 4 clips to install the front door scuff plate outside.
| 34. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 35. INSTALL BACK DOOR WEATHERSTRIP |
Install the back door weatherstrip as shown in the illustration.
| 36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Install the rear door opening trim weatherstrip as shown in the illustration.
| 37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
- HINT:
- Use the same procedures described for the LH side.
| 38. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip as shown in the illustration.
| 39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
- HINT:
- Use the same procedures described for the LH side.
| 40. INSTALL ROOF HEADLINING ASSEMBLY |
- HINT:
When installing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.
When installing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.
After moving the seats, disconnect the cable from the negative (-) battery terminal.
Place the headlining in the cabin from the rear of the vehicle as shown in the illustration.
- NOTICE:
- Be careful not to damage the roof headlining when placing it in the cabin.
for 3 Person Seat Type Rear No. 2 Seat:
Attach the 2 guides, 12 claws and 2 clips to install the headlining.
except 3 Person Seat Type Rear No. 2 Seat:
Attach the 2 guides, 12 claws and 3 clips to install the headlining.
w/ Rear Wiper:
Connect the washer hose.
Connect the antenna cord connector.
Connect the antenna cord connector and attach the 2 clamps.
Install the bolt.
Connect the 3 roof wire connectors and 4 clamps.
w/ Rear Wiper:
Connect the washer hose.
w/ Rain Sensor:
Connect the rain sensor connector.
w/ EC Mirror:
Connect the inner mirror connector.
| 41. INSTALL FRONT ROOF SIDE RAIL GARNISH LH |
Install 3 new clips to the roof side rail garnish.
Attach the 3 clips to install the roof side rail garnish.
| 42. INSTALL FRONT ROOF SIDE RAIL GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 43. INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure to install the 3rd seat assist grip on the other side.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
| 44. INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH |
w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:
Install the No. 2 assist grip assembly.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
w/ Rear No. 2 Seat, for Face to Face Seat Type:
Install the No. 2 assist grip assembly.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
| 45. INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 46. INSTALL ASSIST GRIP ASSEMBLY |
- HINT:
- Use the same procedure to install the assist grip on the other side.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
| 47. INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat) |
Attach the 4 guides and 4 clips to install the seat belt anchor cover.
| 48. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) |
Push in the stopper in the direction of the arrow labeled (1) to install the rain sensor cover.
Slide the No. 2 cover in the direction of the arrow labeled (2) to fix it in place.
| 49. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
Attach the 2 claws to install the cover.
| 50. INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor) |
Attach the 2 clips to install the center visor.
| 51. INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor) |
- HINT:
- Use the same procedures described for the LH side.
| 52. INSTALL VISOR HOLDER |
- HINT:
- Use the same procedures to install the visor holder on the other side.
Attach the 2 claws.
Push the visor holder in to install it.
| 53. INSTALL VISOR ASSEMBLY LH |
Install the visor with the 2 screws.
| 54. INSTALL VISOR ASSEMBLY RH |
- HINT:
- Use the same procedures described for the LH side.
| 55. INSTALL VISOR BRACKET COVER |
- HINT:
- Use the same procedure to install the visor bracket cover on the other side.
Attach the 4 claws to install the visor bracket cover.
| 56. INSTALL NO. 2 ROOM LIGHT ASSEMBLY |
Install the 2 covers.
Attach the 4 claws to install the room light lens.
Attach the 4 claws to install the room light to the room light switch base.
Attach the 4 claws to install the room light.
| 57. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
w/ Map Light:
Install the No. 1 room light assembly.
Connect the connector.
Attach the 4 clips to install the room light.
w/o Map Light:
Install the No. 1 room light assembly.
Install the 2 covers.
Attach the 4 claws to install the room light lens.
Attach the 4 claws to install the room light to the room light switch base.
Attach the 4 claws to install the room light.
| 58. INSTALL MAP LIGHT ASSEMBLY (w/ Map Light) |
Connect the connector.
Attach the 2 clips and 2 guides to install the map light.
Install the 2 screws.
Attach the 2 claws to close the 2 covers.
| 59. INSTALL REAR UPPER PILLAR GARNISH LH |
Attach the 5 clips to install the rear upper pillar garnish.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the seat belt shoulder anchor cover.
| 60. INSTALL REAR UPPER PILLAR GARNISH RH |
w/o Power Back Door:
Attach the 5 clips to install the rear upper pillar garnish.
w/ Power Back Door:
Pass the power back door rod through the rear upper pillar garnish.
Attach the 5 clips to install the rear upper pillar garnish.
Install the seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the seat belt shoulder anchor cover.
| 61. INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door) |
Install the back door stay plate.
Pass the power back door rod through the hole of the back door service hole cover RH and install the rod with the bolt.
- Torque:
- :
- 18 N*m{ 184 kgf*cm, 13 ft.*lbf}
Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.
Attach the 2 clips and install the back door service hole cover RH.
- NOTICE:
- If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover, so do not perform this operation with the back door in a fully open position.
| 62. INSTALL BACK DOOR SIDE GARNISH RH (w/ Power Back Door) |
w/o Power Back Door:
- HINT:
- Use the same procedure described for the LH side.
w/ Power Back Door:
Attach the clip and 4 claws to install the back door side garnish RH.
| 63. INSTALL CENTER BACK DOOR GARNISH (w/ Power Back Door) |
Attach the 5 clips and 4 claws to install the center back door garnish.
| 64. INSTALL REAR FRONT QUARTER TRIM GARNISH LH |
Pass the seat belt anchor through the quarter trim garnish.
Attach the clip and 2 guides to install the quarter trim garnish.
Install the screw.
| 65. INSTALL REAR FRONT QUARTER TRIM GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 66. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm, 9 ft.*lbf}
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Tonneau Cover:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
| 67. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm, 9 ft.*lbf}
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Tonneau Cover:
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
Install the rear No. 1 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
| 68. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 69. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
- HINT:
- Use the same procedure to install the tonneau cover holder cap on the other side.
Attach the 2 claws to install the tonneau cover holder cap.
| 70. INSTALL CENTER PILLAR GARNISH LH |
Pass the seat belt anchor through the center pillar garnish.
Attach the 2 clips and 2 guides to install the center pillar garnish.
Install the bolt.
| 71. INSTALL CENTER PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 72. INSTALL REAR ASSIST GRIP ASSEMBLY |
- HINT:
- Use the same procedure to install the rear assist grip on the other side.
Attach the 2 claws to install the rear assist grip.
Install the 2 bolts.
Attach the 4 claws to install the 2 assist grip plugs.
| 73. INSTALL CENTER LOWER PILLAR GARNISH LH |
- HINT:
When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.
When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
After moving the front seat, disconnect the cable from the negative (-) battery terminal.
Attach the 2 claws and 7 clips to install the center lower pillar garnish.
Install the seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
| 74. INSTALL CENTER LOWER PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 75. INSTALL CENTER PILLAR GARNISH COVER LH |
- HINT:
When installing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.
When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
After moving the front seat, disconnect the cable from the negative (-) battery terminal.
Attach the 2 clips and 2 guides to install the cover.
| 76. INSTALL CENTER PILLAR GARNISH COVER RH |
- HINT:
- Use the same procedures described for the LH side.
| 77. INSTALL FRONT PILLAR GARNISH LH |
for 9, 14 Speakers:
Connect the speaker connector.
Attach the clip and 3 guides to install the front pillar garnish.
| 78. INSTALL FRONT PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 79. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
- HINT:
- Use the same procedure to install the front assist grip on the other side.
Attach the 2 claws to install the front assist grip.
Install the 2 bolts.
Attach the 4 claws to install the 2 assist grip plugs.
| 80. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE |
Attach the 6 clips to install the support plate.
| 81. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
| 82. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 83. INSTALL REAR STEP COVER |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 84. INSTALL FRONT DOOR SCUFF PLATE LH |
Attach the 7 claws and 4 clips to install the scuff plate.
| 85. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 86. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type) |
Install the rear No. 2 seat assembly LH ().
| 87. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 88. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type) |
Install the rear No. 2 seat assembly LH ().
| 89. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 90. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 91. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().