Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT
REAR SEATBACK HEATER (for 60/40 Split Seat Type 60 Side) - INSTALLATION
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
| 1. INSTALL REAR SEATBACK HEATER ASSEMBLY |
Set the seatback heater with the name stamp side facing the seatback cover.
Install the seatback heater with new tack pins.
| 2. INSTALL REAR SEPARATE TYPE SEATBACK COVER |
w/ Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.
- NOTICE:
w/o Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.
- NOTICE:
w/ Rear Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
| 3. INSTALL SEATBACK COVER WITH PAD |
Install the seatback cover with pad.
w/ Center Armrest:
Pull out the seat belt.
w/o Center Armrest:
Pull out the seat belt.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seatback.
Connect the seatback heater wire harness and install a new cable tie.
w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
- NOTICE:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
w/ Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
w/o Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
| 4. INSTALL REAR SEAT BELT HOLE COVER LH |
Attach the 4 claws to install the cover.
Install the screw.
| 5. INSTALL SHOULDER BELT ANCHOR COVER |
Attach the 2 claws to install the cover.
| 6. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
w/ Center Armrest:
Attach the 4 claws to install the 2 supports.
w/o Center Armrest:
Attach the 8 claws to install the 4 supports.
| 7. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 8. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
w/ Center Armrest:
Push the board down to attach the 2 claws on the bottom.
Attach the 2 claws on the top of the board to install it.
w/o Center Armrest:
Push the board down to attach the 3 claws on the bottom.
Attach the 3 claws on the top of the board to install it.
| 9. INSTALL REAR SEATBACK COVER |
Attach the 4 claws to install the cover.
| 10. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seatback cover with pad.
w/ Center Armrest:
Pull out the seat belt.
w/o Center Armrest:
Pull out the seat belt.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seatback.
Connect the seatback heater wire harness and install a new cable tie.
w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
- NOTICE:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
w/ Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
w/o Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
| 11. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
Connect the belt anchor.
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
| 12. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Install the belt with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
- HINT:
- The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.
| 13. INSTALL REAR SEAT UNDER TRAY COVER LH |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 14. INSTALL REAR SEAT CUSHION COVER RH |
Attach the 2 claws to install the cover.
Install the 4 screws.
| 15. INSTALL REAR UNDER SIDE COVER LH |
Attach the 2 claws and 2 clips to install the cover.
Install the 5 screws.
Attach the 10 claws.
| 16. INSTALL REAR SEATBACK STAY COVER LH |
Attach the 2 claws to install the cover.
Install the screw.
| 17. INSTALL SEAT BELT ANCHOR COVER CAP |
Install the anchor cover cap with the screw.
Attach the claw to close the cap.
| 18. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
| 19. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
Attach the cable clamp to connect the cable.
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
w/ Rear Seat Side Airbag:
Attach the wire harness clamp.
w/ Seat Heater System:
Attach the wire harness clamp.
| 20. INSTALL REAR NO. 2 SEAT PROTECTOR |
Install the wire harness, and attach 2 claws to close the protector.
Attach the claw to install the protector to the seat hinge.
Install the clip.
w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.
w/ Seat Heater System:
Attach the claw to install the wire harness connector.
| 21. INSTALL REAR NO. 2 SEAT LEG SIDE COVER |
Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.
Attach the 4 claws to install the seat leg side cover.
Install the 4 screws.
| 22. INSTALL UPPER SEAT TRACK RAIL COVER RH |
Attach the 2 claws to install the cover.
| 23. INSTALL UPPER SEAT TRACK RAIL COVER LH |
Attach the 2 claws to install the cover.
| 24. INSTALL REAR NO. 1 SEAT RECLINING COVER RH |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 25. INSTALL REAR NO. 1 SEAT RECLINING COVER LH |
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the 2 screws.
| 26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
Install the release handle with the screw.
| 27. INSTALL SEAT ADJUSTER BOLT COVER |
Attach the 2 claws to install the cover.
| 28. INSTALL REAR NO. 1 SEAT ASSEMBLY LH |
Install the rear No. 1 seat assembly ().