Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT
REAR SEAT CUSHION HEATER (for 60/40 Split Seat Type 60 Side) - REMOVAL
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
| 1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
Remove the rear No. 1 seat assembly ().
| 2. REMOVE SEAT ADJUSTER BOLT COVER |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
Remove the screw and release handle.
| 4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cover.
| 5. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 6. REMOVE UPPER SEAT TRACK RAIL COVER LH |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 7. REMOVE UPPER SEAT TRACK RAIL COVER RH |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER |
Remove the 4 screws and detach the 4 claws.
Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.
| 9. REMOVE REAR NO. 2 SEAT PROTECTOR |
w/ Rear Seat Side Airbag:
Detach the claw and remove the wire harness connector.
w/ Seat Heater System:
Detach the claw and remove the wire harness connector.
Using a clip remover, remove the clip.
Detach the claw and remove the seat protector from the seat hinge.
Detach the 2 claws, open the protector and remove wire harness.
| 10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
w/ Rear Seat Side Airbag:
Detach the wire harness clamp.
w/ Seat Heater System:
Detach the wire harness clamp.
Remove the 2 nuts and hinge.
Detach the cable clamp and disconnect the cable.
| 11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
Remove the 2 nuts and hinge.
| 12. REMOVE SEAT BELT ANCHOR COVER CAP |
Detach the claw and open the cap.
Remove the screw and anchor cover cap.
| 13. REMOVE REAR SEATBACK STAY COVER LH |
Remove the screw.
Detach the 2 claws and remove the cover.
| 14. REMOVE REAR UNDER SIDE COVER LH |
Detach the 10 claws.
Remove the 5 screws.
Detach the 2 clips and 2 claws, and remove the cover.
| 15. REMOVE REAR SEAT CUSHION COVER RH |
Remove the 4 screws.
Detach the 2 claws and remove the cover.
| 16. REMOVE REAR SEAT UNDER TRAY COVER LH |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Remove the bolt and belt.
- HINT:
- The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.
| 18. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
Disconnect the belt anchor.
| 19. REMOVE SEAT CUSHION COVER WITH PAD |
w/ Rear Seat Side Airbag:
Detach the side airbag wire harness clamps.
Remove the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.
Remove the seatback heater wire harness through the hole in the seat cushion.
Remove the seat cushion cover with pad.
| 20. REMOVE REAR SEPARATE TYPE SEAT CUSHION COVER |
Detach the 3 pieces of fastening tape.
Remove the hog rings and cover.
| 21. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY |
Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.