Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT BELT
REAR NO. 1 SEAT OUTER BELT ASSEMBLY - REMOVAL
- HINT:
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 4. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
Remove the rear No. 2 seat assembly ().
| 5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
Detach the 6 clips and remove the support plate.
| 6. REMOVE REAR STEP COVER |
- HINT:
- Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
| 7. REMOVE REAR DOOR SCUFF PLATE LH |
Remove the screw.
Detach the 3 claws and 4 clips, and remove the scuff plate.
| 8. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
- HINT:
- Use the same procedure to remove the tonneau cover holder cap on the other side.
Detach the 2 claws and remove the tonneau cover holder cap.
| 9. REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat) |
Detach the 6 clips and remove the rear No. 2 seat cover bezel.
| 10. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
- HINT:
- When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
Detach the 3 claws and remove the cover.
Remove the bolt and disconnect the rear seat outer belt floor anchor.
w/ Rear No. 2 Seat, for LH side:
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor LH.
w/ Rear No. 2 Seat, for RH side:
Detach the 3 claws and remove the cover.
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor RH.
w/o Tonneau Cover:
Remove the clip and bolt.
Detach the 18 clips and 2 claws.
w/o Rear Air Conditioning System:
Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.
w/ Rear Air Conditioning System:
Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.
w/ Tonneau Cover:
Remove the screw and clip.
Detach the 18 clips and 2 claws, and remove the quarter trim panel.
| 11. REMOVE REAR FRONT QUARTER TRIM GARNISH LH |
Remove the screw.
Detach the clip and 2 guides.
Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.
| 12. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH |
Remove the nut and seat belt shoulder anchor.
w/ Pretensioner:
Disconnect the pretensioner connector as shown in the illustration.
Remove the 2 bolts and rear No. 1 seat outer belt.
| 13. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
Remove the 2 bolts and anchor plate.