Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - METER / GAUGE / DISPLAY
METER / GAUGE SYSTEM - OPERATION CHECK
| INSPECT INDICATOR/WARNING LIGHT |
Check the following indicators and warning lights.
| Indicator/Warning Light | Switch Condition | Specified Condition |
| A/T OIL TEMP warning light*1 | Ignition switch off → ON | Comes on for 3 seconds |
| BRAKE warning light | ||
| ABS warning light | ||
| OIL LEVEL indicator light | ||
| FUEL FILTER & SEDIMENTER indicator light*2 | ||
| SLIP indicator light*3 | ||
| VSC OFF indicator light*3 | ||
| WASHER indicator light | ||
| RSCA OFF indicator light*4 | ||
| CRAWL indicator light*3 | ||
| SPEED LIMIT indicator light | ||
| Eco driving indicator light | ||
| TRC OFF indicator light*3 | ||
| Turn assist indicator light*3 | ||
| Multi-terrain select indicator light*5 | ||
| SRS warning light | Ignition switch off → ON | Comes on for 6 seconds |
| CHARGE warning light | Ignition switch off → ON | Illuminates when ignition switch is turned to ON. Turns off when engine is started. |
| MIL |
| Indicator/Warning Light | Switch Condition | Specified Condition |
| BRAKE warning light | Ignition switch off → ON | Comes on for 3 seconds |
| ABS warning light | ||
| SLIP indicator light | ||
| RSCA OFF indicator light*1 | ||
| CRAWL indicator light | ||
| SPEED LIMIT indicator light | ||
| PCS indicator light*2 | ||
| Eco driving indicator light | ||
| VSC OFF indicator light | ||
| Turn assist indicator light | ||
| Multi-terrain select indicator light*4 | ||
| Headlight beam level control system warning light*3 | ||
| Tire pressure warning light*5 | ||
| SRS warning light | Ignition switch off → ON | Comes on for 6 seconds |
| CHARGE warning light | Ignition switch off → ON | Illuminates when ignition switch is turned to ON. Turns off when engine is started. |
| MIL |
| INSPECT SPEEDOMETER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
- Reference:
mph: Standard Indication Acceptable Range 20 mph 18.5 to 22 mph 40 mph 39.5 to 42.5 mph 60 mph 59.5 to 63 mph 80 mph 80.5 to 84.5 mph 100 mph 100.5 to 105.5 mph 120 mph 119.5 to 126 mph 140 mph 141 to 147 mph km/h (except Australia): Standard Indication Acceptable Range 20 km/h 21 to 25 km/h 40 km/h 41.7 to 46.2 km/h 60 km/h 62.7 to 67.2 km/h 80 km/h 83.4 to 88.4 km/h 100 km/h 104.3 to 109.3 km/h 120 km/h 125.1 to 130.6 km/h 140 km/h 145.8 to 151.8 km/h 160 km/h 166.2 to 173.2 km/h 180 km/h 186.9 to 194.5 km/h 200 km/h 207.7 to 215.7 km/h 220 km/h 228.4 to 236.8 km/h 240 km/h 249.2 to 258 km/h km/h (for Australia): Standard Indication Acceptable Range 20 km/h 17.5 to 21.5 km/h 40 km/h 38 to 42 km/h 60 km/h 58 to 63 km/h 80 km/h 78 to 84 km/h 100 km/h 98.5 to 104.5 km/h 120 km/h 119 to 125 km/h 140 km/h 139 to 146 km/h 160 km/h 159 to 167 km/h 180 km/h 186.9 to 194.5 km/h 200 km/h 199 to 209 km/h 220 km/h 219 to 230 km/h 240 km/h 239 to 251 km/h
If the result is not as specified, the speedometer may have a malfunction.
- NOTICE:
- Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.
Check the deflection width of the speedometer indicator.
- Reference:
- Within 0.3°
| INSPECT TACHOMETER |
Connect a tune-up tachometer, and start the engine.
Compare the test results with the tachometer indicator.
| Standard indication (rpm) | Acceptable range Data in ( ) is for reference |
| 700 | 630 to 770 |
| 1000 | (900 to 1100) |
| 2000 | (1850 to 2150) |
| 3000 | 2800 to 3200 |
| 4000 | (3800 to 4200) |
| 5000 | 4800 to 5200 |
| 6000 | (5750 to 6250) |
If the result is not as specified, the tachometer may have a malfunction.
| INSPECT METER/GAUGE |
Connect the intelligent tester to the DLC3.
Perform Active Test ().
- OK:
- Each meter/gauge needle indication is normal.
| INSPECT WARNING/INDICATOR LIGHT |
Connect the intelligent tester to the DLC3.
Perform Active Test ().
- OK:
- Each warning/indicator light turns on and off using the intelligent tester.
| INSPECT ENGINE OIL LEVEL WARNING (except 3UR-FE) |
Turn the ignition switch to ON and warm up the engine at an engine speed of 2000 rpm or less until the coolant temperature reaches approximately 80°C (176°F) or more.
Disconnect the engine oil level sensor connector for 40 seconds or more.
Turn the ignition switch to ON and check the multi-information display.
- OK:
- Low engine oil level message is displayed.
| INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information Display) |
Connect the intelligent tester to the DLC3.
Perform Active Test ().
- HINT:
- If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end Active Test and turn the ignition switch off.
- OK:
- All dots in the multi-information display turn on and off using the intelligent tester.