Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - METER / GAUGE / DISPLAY
METER / GAUGE SYSTEM - DATA LIST / ACTIVE TEST
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ODO/TRIP Change SW | Trip switch (ODO/TRIP switch) condition / ON or OFF | ON: Trip switch (ODO/TRIP switch) pushed OFF: Trip switch (ODO/TRIP switch) not pushed | - |
| Tail Cancel SW | TAIL cancel switch condition / ON or OFF | ON: TAIL cancel switch on OFF: TAIL cancel switch off | - |
| Washer Switch | Washer switch / ON or OFF | ON: Washer switch on OFF: Washer switch off | - |
| P-Seatbelt Buckle SW | Front passenger side seat belt warning light request signal / ON or OFF | ON: Tongue plate (for front passenger side) inserted OFF: Tongue plate (for front passenger side) not inserted | - |
| Oil Level SW | Oil level switch / ON or OFF | ON: Oil level switch on OFF: Oil level switch off | - |
| Water Level SW | Water level switch / ON or OFF | ON: Water level switch on OFF: Water level switch off | - |
| Multi Display Select Switch | Steering multi-display select switch / ON or OFF | ON: Steering multi-display select switch on OFF: Steering multi-display select switch off | - |
| Vehicle Speed Meter | Vehicle speed / Min.: 0 (0), Max.: 255 (158) | Almost same as actual vehicle speed (when driving) | Unit: km/h (mph) |
| Engine Rpm | Engine speed / Min.: 0, Max.: 12750 | Idling: 700 to 800 | Unit: rpm |
| Coolant Temperature | Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284) | After warming up: 80 to 105 (176 to 221) | Unit: °C (°F). If the value is -40 (-40): The sensor circuit is open. If the value is 140 (284): The sensor circuit is shorted. |
| Fuel Input | Fuel sender gauge input / Min.: 0, Max.: 127.5 | Fuel sender input value | Unit: L |
| Rheostat value | Light control rheostat switch input / Min.: 0, Max.: 100 | Light control rheostat switch is fully turned right (0) → fully turned left (100) | Unit: % |
| Communication ECM/Meter DTC 3 | ECM communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ECM ODO (History 3) | ECM odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Communication ECM/Meter DTC 2 | ECM communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ECM ODO (History 2) | ECM odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Communication ECM/Meter DTC 1 | ECM communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ECM ODO (History 1) | ECM odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Communication ABS/Meter DTC 3 | Skid control ECU communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ABS/VSC ODO (History 3) | Skid control ECU odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Communication ABS/Meter DTC 2 | Skid control ECU communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ABS/VSC ODO (History 2) | Skid control ECU odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Communication ABS/Meter DTC 1 | Skid control ECU communication stop history / Rec or Unrec | Rec: DTC is stored Unrec: DTC is not stored | - |
| ABS/VSC ODO (History 1) | Skid control ECU odometer history / Min.: 0, Max.: 999999 | With history: 0 to 999999 Without history: ffffffh | - |
| Units By Region | Unit of display setting / Km/l JP, Km/l, Mi/g US or Mi/g UK | Displays unit setting | - |
| Language | Language of display setting / English, Spanish, French*, German* or Italian* | Displays language setting | - |
| Driver Side Seatbelt Warning Buzzer | Driver side seat belt warning buzzer setting / ON or OFF | ON: Driver side seat belt warning buzzer on setting OFF: Driver side seat belt warning buzzer off setting | - |
| P-Seatbelt Warning Buzzer | Front passenger side seat belt warning buzzer setting / ON or OFF | ON: Front passenger side seat belt warning buzzer on setting OFF: Front passenger side seat belt warning buzzer off setting | - |
| Sub Fuel Input | Fuel sender gauge input / Min.: 0, Max.: 127.5 | Fuel sender input value | Unit: L |
| Integrated value for Oil Maintenance | Oil maintenance warning integrated value / Min.: 0 (0), Max.: 25500 (41037) | 0 (0) to 25500 (41037) | Unit: mile |
| Integrated value for Timing belt | T-belt indicator integrated value / Min.: 0, Max.: 6553500 | 0 to 6553500 | Unit: km/h |
| +B Voltage Value | +B voltage / Min.: 0, Max.: 25.5 | 11 to 14 | Unit: V |
| Coolant Temperature | Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284) | After warming up: 80 to 105 (176 to 221) | Unit: °C (°F) If the value is -40 (-40): The sensor circuit is open. If the value is 140 (284): The sensor circuit is shorted. |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Engine Rpm | Engine speed / Min.: 0, Max.: 16383.75 | Idling: 700 to 800 | Unit: rpm |
| Vehicle Speed Meter | Vehicle speed / Min.: 0 (0), Max.: 255 (158) | Actual vehicle speed | Unit: km/h (mph) The speed is indicated on the speedometer. |
| Coolant Temperature*1 | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 100°C (176 to 212): After warming up | If the value is -40°C (-40°F), The sensor circuit is open. If the value is 140°C (284°F) or higher, The sensor circuit is shorted. |
| Coolant Temperature*2 | Engine coolant temperature / Min.: -40°C, Max.: 140°C | After warming up engine: 75 to 90°C (167 to 194°F) | If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal. |
- HINT:
- *1: except 1VD-FTV
- *2: for 1VD-FTV
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body Electrical / (Combination Meter) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Speed Meter Operation*1 | Speedometer | 0, 40, 80, 120, 160, 200, 240 or 280 | Perform the test with the vehicle stopped and engine idling. |
| Tachometer operation | Tachometer | 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 | Perform the test with the vehicle stopped and engine idling. |
| Fuel Meter Operation | Fuel receiver gauge | EMPTY, 1/4, FULL | Perform the test with the vehicle stopped and engine idling. |
| Volt Meter Operation | Voltmeter | 0, 3, 6, 9, 12, 15 or 18 | Perform the test with the vehicle stopped and engine idling. |
| Oil Pressure Meter Operation | Oil pressure receiver gauge | LOW, 1/4, 1/2, 3/4 or HIGH | Perform the test with the vehicle stopped and engine idling. |
| A/T Indicator operation (1)*10 | A/T indicator (normal mode) | P, R, N, D, 4, 3, 2, L | Perform the test with the vehicle stopped and engine idling. |
| A/T Indicator operation (2)*10 | A/T indicator (sequential mode) | Es, 5 or 6 | Perform the test with the vehicle stopped and engine idling. |
| Meter Display 1*2 | All dots in the multi-information display | ALL, 0, 1, 2, 3, 4, 5 or 6 | Perform the test with the vehicle stopped and engine idling. |
| Meter Display 2*2 | All dots in the multi-information display | 7, 8 or 9 | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Beam | BEAM indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Head | HEAD indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Tail | TAIL indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Fr FOG | FRONT FOG indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Airbag | SRS warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Precrash | PCS indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Driver Side Seat Belt | Driver side seat belt warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Front Passenger Side Seat Belt | Passenger side seat belt warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Doors All Open | All doors open light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Washer | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Fuel | Low fuel warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Charge | CHARGE warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp ABS | ABS warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Slip*6 | SLIP indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Tire Pressure Warning System*11 | Tire pressure warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Brake | Brake warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp oil Level | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp ECT PWR | ECT PWR indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| A/T Oil Temperature Operation*10 | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Cruise*7 | Cruise control indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. KEY | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Master Warning | Master warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Clearance Sonar LCD | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. INTUITIVE P/A LCD | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp VSC OFF*6 | Multi-information display | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. 2nd START | 2nd START indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Ctr DIFF LOCK | Center differential lock indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. 4LO | 4LO indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. CRAWL*6 | CRAWL indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. A/T P*10 | A/T P indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | LOW, NORMAL or HIGH | Perform the test with the vehicle stopped and engine idling. |
| Indicat. GLOW*5 | Glow indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Lamp Water Level | Fuel filter and sedimenter indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Over Speed | Speed limit indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| VSC TRC Indicator*6 | TRC OFF indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| PPS Indicator | Power steering warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. ECONO | Eco driving indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. SET*7 | SET indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Radar Cruise Indicator*3 | Radar cruise control indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Rr Inner Wheel Control Indicator*6 | Turn assist indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| OFF Road Guidance Indicator*8 | Multi-terrain select indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Indicat. Headlamp Auto Leveling*4 | Headlight beam level control system warning light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
| Automatic High Beam Indicator*9 | Automatic High Beam Indicator light | ON or OFF | Perform the test with the vehicle stopped and engine idling. |
- HINT:
- *1:
The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
The needle position should be within the acceptable range.
- *2: If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.
- *3: w/ Dynamic Radar Cruise Control System
- *4: w/ Headlight Leveling
- *5: for 1VD-FTV
- *6: w/ VSC
- *7: w/ Cruise Control System
- *8: w/ Multi-terrain Select
- *9: w/ Automatic High Beam System
- *10: for Automatic Transmission
- *11: w/ Tire Pressure Warning System
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Dimmer Signal | Illumination dimming operation | ON or OFF | - |