INSTALL IDLER PULLEY BRACKET (w/ Belt Tension Side)

INSTALL IDLER PULLEY BRACKET

INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

INSTALL IDLER PULLEY ASSEMBLY

INSTALL RADIATOR ASSEMBLY

INSTALL RADIATOR RESERVE TANK ASSEMBLY

INSTALL FAN SHROUD WITH FAN

INSTALL OIL COOLER HOSE (w/ Air Cooled Transmission Oil Cooler)

INSTALL NO. 2 RADIATOR HOSE

INSTALL NO. 1 RADIATOR HOSE

INSTALL VANE PUMP ASSEMBLY

INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

INSTALL V-RIBBED BELT

INSTALL INTAKE AIR CONNECTOR

TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

INSTALL AIR CLEANER CAP SUB-ASSEMBLY

INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

INSTALL NO. 3 ENGINE ROOM WIRE

INSTALL UPPER RADIATOR SUPPORT SEAL

ADD ENGINE COOLANT

INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CHECK FOR ENGINE COOLANT LEAKS

Install the bracket with the 3 bolts.

• Torque:
• 48.5 N*m{ 495 kgf*cm, 36 ft.*lbf}

Install the bracket with the bolt.

• Torque:
• 48.5 N*m{ 495 kgf*cm, 36 ft.*lbf}

Install the heater assembly with the 2 bolts.

• Torque:
• 48.5 N*m{ 495 kgf*cm, 36 ft.*lbf}

Connect the 2 heater hoses.

Using pliers, grip the claws of the clips and slide the 2 clips.

Connect the connector and attach the clamp.

Install the 2 idler pulleys with the 2 bolts.

• Torque:
• 48.5 N*m{ 495 kgf*cm, 36 ft.*lbf}

Install the radiator assembly ().

Install the radiator reservoir with the 3 bolts.

Connect the 2 hoses to the upper radiator tank and water inlet.

• HINT:

• Make sure the directions of the hose clamps are as shown in the illustration.

Install the shroud together with the fluid coupling fan between the radiator and engine components.

• NOTICE:

• Be careful not to damage the radiator core.

Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts.

• HINT:

• Tighten the nuts as much as possible by hand.

Attach the shroud claws to the radiator.

Install the shroud with the 2 bolts.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Tighten the 4 nuts of the fluid coupling fan.

• Torque:
• 21 N*m{ 214 kgf*cm, 15 ft.*lbf}

Temporarily install the oil cooler tube to the fan shroud with the bolt labeled A. Install the bolt labeled B. Then tighten the bolt labeled A to the specified torque.

• Torque:
• 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}

Connect the inlet No. 4 oil cooler hose as shown in the illustration.

• NOTICE:

• Make sure the pinching portion of each clip is facing the direction shown in the illustration.

Connect the inlet No. 2 and No. 3 oil cooler hoses as shown in the illustration.

• NOTICE:

• Make sure the pinching portion of each clip is facing the direction shown in the illustration.

Connect the inlet and outlet No. 1 oil cooler hoses as shown in the illustration.

• NOTICE:

• Make sure the pinching portion of each clip is facing the direction shown in the illustration.

Pass the hose through the flexible hose clamp and close the clamp shown in the illustration.

Apply a light coat of engine oil to a new O-ring, and install it to the vane pump.

Install the vane pump with 2 new nuts.

• Torque:
• 29 N*m{ 296 kgf*cm, 21 ft.*lbf}

Install the vane pump oil reservoir to the bracket.

Install the V-ribbed belt as shown in the illustration.

Temporarily install the lock nut, and turn the bolt clockwise.

Using a belt tension gauge, inspect the belt tension.

• Standard Belt Tension:

• Item	Condition	Specified Condition
  New belt	5 to 35°C (41 to 95°F)	550 to 800 N (56 to 82 kgf, 123.6 to 179.8 lbf)
  Used belt	5 to 35°C (41 to 95°F)	300 to 500 N (31 to 51 kgf, 67.4 to 112.4 lbf)

• HINT:

Tighten the nut.

• Torque:
• 40 N*m{ 408 kgf*cm, 30 ft.*lbf}

Check that the belt fits properly in the ribbed grooves.

• HINT:

• Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

• If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.

Connect the intake air connector to the No. 1 and No. 2 air cleaner pipes.

Install the connector with the 2 bolts.

• Torque:
• 21 N*m{ 214 kgf*cm, 15 ft.*lbf}

Tighten the 2 hose clamps.

• Torque:
• 6.3 N*m{ 64 kgf*cm, 56 in.*lbf}

Attach the 3 wire harness clamps.

Connect the 2 connectors to the water temperature sensor and viscous heater.

Temporarily install the air cleaner hose to the intake air connector.

Align the protrusion of the air cleaner cap and concave portion of the air cleaner hose.

Connect the air cleaner cap to the air cleaner hose, and install the air cleaner cap with the 3 clamps.

Tighten the 2 hose clamps and connect the connector.

• Torque:
• 2.5 N*m{ 25 kgf*cm, 22 in.*lbf}

Install the engine cover with the 2 nuts.

• Torque:
• 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Install the No. 3 engine room wire to the main battery and sub-battery positive terminals with the 2 nuts.

• Torque:
• 7.6 N*m{ 77 kgf*cm, 67 in.*lbf}

Connect the No. 3 engine room wire with the 4 clamps.

Install the radiator support seal with the 7 clips.

Remove the engine air bleed cap.

Connect a clear hose to the engine air bleed pipe.

Using a wrench, remove the vent plug.

Fill the radiator with TOYOTA SLLC to the radiator reservoir filler neck.

• HINT:

• Pour TOYOTA SLLC until it spills out of the engine air bleed pipe.

• Standard Capacity (for Automatic Transmission):

• Item	Specified Condition
  Front heater only	14.8 liters (15.6 US qts, 13.0 Imp. qts)
  Front heater and rear heater	17.6 liters (18.6 US qts, 15.5 Imp. qts)
  Front heater with viscous heater	15.2 liters (16.1 US qts, 13.4 Imp. qts)
  Front heater and rear heater with viscous heater	18.0 liters (19.0 US qts, 15.4 Imp. qts)

• Standard capacity (for Manual Transmission):
• 15.4 liters (16.3 US qts, 13.5 Imp. qts)

• NOTICE:

• Do not substitute plain water for engine coolant.

• HINT:

• TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

Install the vent plug.

• Torque:
• 2.0 N*m{ 20 kgf*cm, 18 in.*lbf}

• NOTICE:

• Do not tighten the plug to 5.0 N*m (51 kgf*cm, 44 in.*lbf) or more, as the plug will be damaged.

Disconnect the clear hose from the engine air bleed pipe.

Install the engine air bleed cap when coolant comes out.

Install the radiator reservoir cap.

Start the engine.

• NOTICE:

• Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

Maintain an engine speed of 3000 rpm for approximately 10 minutes so that the thermostat opens and air bleeding is performed.

• CAUTION:

• NOTICE:

• HINT:

• The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

Stop the engine, and wait until the engine coolant cools down to ambient temperature.

• CAUTION:

• Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

Check that the coolant level is between the FULL and LOW lines.

If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.

Install the No. 1 engine under cover with the 10 bolts.

• Torque:
• 29 N*m{ 296 kgf*cm, 21 ft.*lbf}

for Standard:

Install the front fender splash shield ().

w/ Winch:

Install the front fender splash shield ().

for Standard:

Install the front fender splash shield ().

w/ Winch:

Install the front fender splash shield ().

Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.

Warm up the engine.

Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm², 17.8 psi), and check that the pressure does not drop.

If the pressure drops, check the hoses, radiator and water pump for leaks.

If no external leaks are found, check the cylinder block and cylinder head.