Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT

FRONT SEAT ASSEMBLY (for Power Seat) - REMOVAL

  • CAUTION:
  • Wear protective gloves. Sharp areas on the parts may injure your hands.
  • HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
  • NOTICE:
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().
2. REMOVE FRONT SEAT HEADREST ASSEMBLY

Remove the front seat headrest.

3. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH

Operate the power seat switch (slide switch) to move the front seat assembly LH to the foremost position.

Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 2 claws and remove the rear outer seat track bracket cover LH.

  • HINT:
  • Tape the screwdriver tip before use.
4. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH
Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 2 claws and remove the rear inner seat track bracket cover LH.

  • HINT:
  • Tape the screwdriver tip before use.
5. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH

Operate the power seat switch (slide switch) to move the front seat assembly LH to the rearmost position.

Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 2 claws and remove the front outer seat track bracket cover LH.

  • HINT:
  • Tape the screwdriver tip before use.
6. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH
Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 2 claws and remove the front inner seat track bracket cover LH.

  • HINT:
  • Tape the screwdriver tip before use.
7. REMOVE FRONT SEAT ASSEMBLY LH

Disable the Autoaway/Return function by changing the customize parameter ().

  • NOTICE:
  • Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.
  • HINT:
  • Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully retract and tilt up the steering column assembly.

Turn the ignition switch off.

Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 bolts.

Operate the power seat switch (slide switch) to move the front seat assembly LH to the foremost position.

Front Seat Assembly (For Power Seat) - Removal. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 bolts.

Operate the power seat switch (slide switch) and move the front seat assembly LH to the center position, and operate the power seat switch (reclining switch) and move the seatback to the upright position.

Disconnect the cable from the negative (-) battery terminal.

  • CAUTION:
  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().

Disconnect the connectors under the front seat assembly LH.

Remove the front seat assembly LH from the vehicle.

  • NOTICE:
  • Be careful not to damage the vehicle body.
SEAT
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
FRONT SEAT ASSEMBLY for Power Seat