Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT

FRONT SEAT ASSEMBLY (for Power Seat) - REASSEMBLY

  • CAUTION:
  • Wear protective gloves. Sharp areas on the parts may injure your hands.
  • HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart ().
1. INSTALL FRONT SEAT WIRE LH

Attach the claw to install the front seat wire LH.

Attach the wire harness clamps and connect the connectors.

2. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH
  • CAUTION:
  • Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the front seat airbag assembly with 2 nuts.

  • Torque:
  • 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}

Attach the 2 clamps to connect the wire harness.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 5 clamps to connect the wire harness.

3. INSTALL SEAT POSITION SENSOR (for Driver Side)

Check that the ignition switch is off.

Check that the cable is disconnected from the battery negative (-) terminal.

  • CAUTION:
  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a 1.0 mm (0.0393 in.) feeler gauge, install the seat position sensor.

  • NOTICE:
If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
  • HINT:
  • Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

Using a T30 "TORX" socket wrench, install the seat position sensor with the screw.

  • Torque:
  • 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

Check that there is no looseness in the installation parts of the seat position sensor.

Connect the connector.

Install the seat slide position sensor protector to the seat position sensor.

4. INSTALL SEAT FRAME SET BRACKET SUB-ASSEMBLY (w/ Climate Control Seat System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 hooks to install the seat frame set bracket sub-assembly.

5. INSTALL NO. 1 AIR FILTER (w/ Climate Control Seat System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Rotate the No. 1 air filter clockwise to attach the claws and install it.

6. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the seat climate control blower LH with the nut.

Attach the wire harness clamp.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the 2 bolts and connect the connector.

7. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seat Cushion)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the seat climate control controller LH with the 2 screws.

Attach the wire harness clamp.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 claws to connect the seat climate control blower LH.

8. INSTALL SEAT CLIMATE CONTROL ECU (w/ Climate Control Seat System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw to install the seat climate control ECU.

Connect the connector.

9. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw to install the seat heater control sub-assembly.

Attach the wire harness clamp and connect the connector.

10. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the hook to install the front lower seat cushion shield LH.

Install the screw.

11. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

Attach the hook to install the front lower seat cushion shield RH.

Install the screw.

12. INSTALL UPPER ACTIVE HEADREST UNIT
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the upper active headrest unit with the 4 nuts.

  • Torque:
  • 14 N*m{ 143 kgf*cm, 10 ft.*lbf}
13. INSTALL LOWER ACTIVE HEADREST UNIT
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the lower active headrest unit with the 2 nuts.

  • Torque:
  • 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the clamp.

Connect the active headrest cable to the upper active headrest unit with the nut.

  • Torque:
  • 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
14. INSTALL BUSH (for Driver Side)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 3 claws to install the bush.

15. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the lumbar support adjuster LH with the 2 screws.

Connect the connector.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 hooks to install the seatback spring.

Text in Illustration
*1Cable Clamp
*2Hook

Install the 4 springs.

Connect the active headrest cable to the seatback spring with the cable clamp.

16. INSTALL OUTSIDE RECLINING ADJUSTER COVER LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw to install the outside reclining adjuster cover LH.

Install the screw.

17. INSTALL OUTSIDE RECLINING ADJUSTER COVER RH

Attach the claw to install the outside reclining adjuster cover RH.

Install the screw.

18. INSTALL INSIDE RECLINING ADJUSTER COVER LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw to install the inside reclining adjuster cover LH.

Install the 2 screws.

Attach the wire harness clamp.

19. INSTALL INSIDE RECLINING ADJUSTER COVER RH

Attach the claw to install the inside reclining adjuster cover RH.

Install the 2 screws.

Attach the wire harness clamp.

20. INSTALL FRONT SEATBACK PROTECTOR
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Apply double-sided tape as shown in the illustration.

Text in Illustration
*1Double-sided tape

Install the front seatback protector.

21. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Set the seatback heater with the name stamp side facing the front separate type seatback cover.

w/o Climate Control Seat System:


Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*1Tack Pin*2Front Separate Type Seatback Cover
*3Front Seatback Heater Assembly LH*4Name Stamp

w/ Climate Control Seat System:


Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*1Tack Pin*2Front Separate Type Seatback Cover
*3Front Seatback Heater Assembly LH*4Name Stamp
22. INSTALL FRONT SEPARATE TYPE SEATBACK COVER
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the fastening tape to install the front separate type seatback cover.

Text in Illustration
*1Hog Ring Pliers
*2Fastening Tape

Using hog ring pliers, install new hog rings.

  • NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Pass the seatback cover bracket through the hole of the front separate type seatback pad.

Text in Illustration
*1Seatback Cover Bracket
23. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with new hog rings.

Text in Illustration
*1Hog Ring Pliers
  • NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Pass the seatback cover bracket through the hole of the front separate type seatback pad.

Text in Illustration
*1Seatback Cover Bracket
24. INSTALL SEATBACK COVER WITH PAD
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the hooks to install the seatback cover with pad.

Text in Illustration
*1Hog Ring
*2Hog Ring Pliers
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the seatback cover bracket with the nut.

Text in Illustration
*1Seatback Cover Bracket
  • Torque:
  • 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
  • CAUTION:
  • After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

Using hog ring pliers, install new hog rings.

  • NOTICE:
  • Be careful not to damage the cover.
25. INSTALL FRONT SEAT HEADREST SUPPORT
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 claws to install the 2 front seat headrest supports.

26. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seatback)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 hooks to install the seat climate control controller LH.

Attach the 2 claws to connect the seat climate control blower LH.

27. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

Install the 2 screws.

28. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Set the front seat cushion heater assembly LH with the name stamp side facing the front separate type seat cushion cover.

w/o Climate Control Seat System:


Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*1Tack Pin*2Front Separate Type Seat Cushion Cover
*3Front Seat Cushion Heater Assembly LH*4Name Stamp

w/ Climate Control Seat System:


Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*1Tack Pin*2Front Separate Type Seat Cushion Cover
*3Front Seat Cushion Heater Assembly LH*4Name Stamp
29. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat cushion pad with new hog rings.

Text in Illustration
*1Hog Ring Pliers
  • NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
30. INSTALL SEAT CUSHION COVER WITH PAD

Set the seat cushion cover with pad in place.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the hooks to install the seat cushion cover with pad.

Bend the 2 seat frame claws downward.

for Front Passenger Side:

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 clamps to connect the connector holder.

Connect the connector.

w/o Climate Control Seat System:

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the connector and attach the wire harness clamp.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the connector and attach the 2 wire harness clamps.

w/ Climate Control Seat System:

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the wire harness clamp.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the 2 connectors and attach the 4 wire harness clamps.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the 2 clips.

31. INSTALL FRONT POWER SEAT SWITCH LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the front power seat switch LH with the 3 screws.

w/ Seat Position Memory System:


Connect the 2 connectors.

w/o Seat Position Memory System:


Connect the connector.

32. INSTALL FRONT INNER SEAT CUSHION SHIELD LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 claws and clip to install the front inner seat cushion shield LH.

Install the screw.

33. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Install the front seat belt anchor plate.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the front seat inner belt assembly with the nut.

  • Torque:
  • 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
  • NOTICE:
  • Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

Connect the connectors and attach the clamps.

34. INSTALL LUMBAR SWITCH (for Driver Side)
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the lumbar switch to the front seat cushion shield LH with the 2 screws.

35. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw to install the front inner No. 1 cushion shield LH to the front seat cushion shield LH.

Install the screw.

36. INSTALL FRONT SEAT CUSHION SHIELD LH

for Driver Side:


Connect the connector.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

Install the 3 screws.

Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the 2 rubber bands.

Install the 2 screws.

37. INSTALL RECLINING POWER SEAT SWITCH KNOB
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 claws to install the reclining power seat switch knob.

38. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Front Seat Assembly (For Power Seat) - Reassembly. SEAT. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 claws to install the slide and vertical power seat switch knob.

SEAT
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
FRONT SEAT ASSEMBLY for Power Seat