Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT
FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) - DATA LIST / ACTIVE TEST
DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Driver Side SET Mem SW | Driver side seat memory SET switch / ON or OFF | ON: Driver side seat memory SET switch on OFF: Driver side seat memory SET switch off | - |
Driver Side Memory SW 1 | Driver side seat memory switch 1 / ON or OFF | ON: Driver side seat memory switch 1 on OFF: Driver side seat memory switch 1 off | - |
Driver Side Memory SW 2 | Driver side seat memory switch 2 / ON or OFF | ON: Driver side seat memory switch 2 on OFF: Driver side seat memory switch 2 off | - |
Driver Side Memory SW 3 | Driver side seat memory switch 3 / ON or OFF | ON: Driver side seat memory switch 3 on OFF: Driver side seat memory switch 3 off | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off | - |
Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off | - |
Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off | - |
Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off | - |
Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off | - |
Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off | - |
Slide Rear | Sliding switch signal (Rearward) / ON or OFF | ON: Sliding switch (Rearward) on OFF: Sliding switch (Rearward) off | - |
Slide Front | Sliding switch signal (Forward) / ON or OFF | ON: Sliding switch (Forward) on OFF: Sliding switch (Forward) off | - |
SET Switch | Seat memory SET switch signal / ON or OFF | ON: Seat memory SET switch on OFF: Seat memory SET switch off | - |
M1 Switch | Seat memory switch 1 signal / ON or OFF | ON: Seat memory switch 1 on OFF: Seat memory switch 1 off | - |
M2 Switch | Seat memory switch 2 signal / ON or OFF | ON: Seat memory switch 2 on OFF: Seat memory switch 2 off | - |
M3 Switch | Seat memory switch 3 signal / ON or OFF | ON: Seat memory switch 3 on OFF: Seat memory switch 3 off | - |
Seat Memory No1 | Seat position memorized with seat memory switch 1 / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | - |
Seat Memory No2 | Seat position memorized with seat memory switch 2 / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | - |
Seat Memory No3 | Seat position memorized with seat memory switch 3 / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | - |
Ignition Switch | Communication state of engine switch signal / ON or OFF | ON: Engine switch on (IG) signal is received OFF: Engine switch off signal is not received | - |
Key Switch | Engine switch status (IG) / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
Key Code Conf | Recognition code is registered / ON or OFF | ON: One more recognition codes registered OFF: No recognition code registered | - |
D-Door Courtesy | Door courtesy switch signal / ON or OFF | ON: Driver side door open OFF: Driver side door closed | - |
P Switch | Shift lever position P signal / ON or OFF | ON: Shift lever in P OFF: Shift lever not in P | - |
Parking Brake SW | Parking brake switch status / ON or OFF | ON: Parking brake operated OFF: Parking brake released | - |
Vehicle Speed | Vehicle speed data / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
Power Voltage | Power supply for driver seat ECU / MIN: 0 V, MAX: 19.89 V | Within range from 11 V to 14 V | - |
Slide Position | Seat sliding position / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Reclining Position | Seatback position / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Front Vertical Position | Seat front vertical position / MIN: 4096 MAX: 61440 | Within range from 4096 to 61440 | - |
Lifter Position | Seat lifter position / MIN: 4096 MAX: 61440 | Within range from 4096 to 61440 | - |
Slide Pos Mem No1 | Seat sliding position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Reclining Pos Mem No1 | Seatback position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Frnt Vrtcl Pos Mem No1 | Front vertical position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Lifter Pos Mem No1 | Lifter position memorized with seat memory switch 1 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Slide Pos Mem No2 | Seat sliding position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Reclining Pos Mem No2 | Seatback position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Frnt Vrtcl Pos Mem No2 | Front vertical position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Lifter Pos Mem No2 | Lifter position memorized with seat memory switch 2 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Slide Pos Mem No3 | Seat sliding position memorized with seat memory switch 3 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Reclining Pos Mem No3 | Seatback position memorized with seat memory switch 3 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Frnt Vrtcl Pos Mem No3 | Front vertical position memorized with seat memory switch 3 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
Lifter Pos Mem No3 | Lifter position memorized with seat memory switch 3 / MIN: 4096, MAX: 61440 | Within range from 4096 to 61440 | - |
ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Tester Display | Test Part | Control Range | Diagnostic Note |
Seat Reclining | Seat reclining operation | Front / OFF / Rear | - |
Front Vertical Operation | Seat front vertical operation | Up / OFF / Down | - |
Lifter Operation | Seat lifter operation | Up / OFF / Down | - |
Seat Slide Operation | Seat sliding operation | Front / OFF / Rear | - |
Buzzer | Buzzer operation | ON / OFF | - |