Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - THEFT DETERRENT / KEYLESS ENTRY
ENTRY AND START SYSTEM (for Start Function) - DATA LIST / ACTIVE TEST
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Engine switch on (ACC)/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| IG SW | Engine switch on (IG)/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Stop Light SW | Stop light switch/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Start Switch1 | Start switch 1/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Start Switch2 | Start switch 2/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Steering Unlock Switch | Steering lock condition/ON or OFF | ON: Steering unlocked OFF: Steering locked | - |
| Neutral SW/ Clutch SW | Park/neutral position switch (A/T), clutch start switch (M/T)/ON or OFF | ON: Shift lever in P or N (A/T), clutch pedal depressed (M/T) OFF: Shift lever not in P or N (A/T), clutch pedal released (M/T) | - |
| Shift P Signal | Shift P position signal/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P | - |
| Vehicle Speed Signal | Vehicle speed signal/STOP or RUN | STOP: Vehicle stopped RUN: Vehicle running | - |
| Engine Condition | Engine condition/STOP or RUN | STOP: Engine stopped RUN: Engine running | - |
| IG1 Relay Monitor(Outside) | IG1 No. 3 relay outer relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Monitor(Outside) | Integration relay (IG2 relay) outer relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG1 Relay Monitor(Inside) | IG1 No. 3 relay inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Monitor(Inside) | Integration relay (IG2 relay) inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| ACC Relay Monitor | ACC relay monitor/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| Latch Circuit | Latch circuit/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off, on (ACC) | - |
| Starter Request Signal | Starter request signal/ON or OFF | ON: ST relay ON OFF: ST relay OFF | - |
| Power Supply Condition | Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON | ALL OFF: All relays OFF ACC ON: ACC relay ON IG2 ON: Integration relay (IG2 relay) ON ST ON: STSW signal ON | - |
| ACC Relay Cut Signal | ACC relay cut signal/ON or OFF | ON: Engine cranking OFF: Engine not cranking | - |
| Starter Relay Monitor | ST relay monitor/ON or OFF | ON: Engine cranking OFF: Engine not cranking | - |
| Communication Smart/Wireless | Communication to certification ECU (smart key ECU assembly)/OK or STOP | OK: Communication STOP: No communication | - |
| The Number of DTC | Number of diagnostic trouble codes/Min: 0, Max: 255 | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Unmatched Vehicle-ID | Key ID/YES or NO | YES: Key ID matches NO: Key ID differs | - |
| No Response | No Communication condition between vehicle and electrical key transmitter (response) / Yes or No | Yes: Key ID code not matched to vehicle No: Key ID code matched to vehicle | - |
| Unmatch Code or Form | Code format/YES or NO | YES: Code format matches NO: Code format differs | - |
| Key Low Battery | Key battery conditions/Yes or No | Yes: Key battery voltage low No: Key battery voltage normal | - |
| #Codes | Number of diagnostic trouble codes/Min: 0, Max: 255 | - | - |
| ID Code Difference(Resp) | ID code/YES or NO | YES: ID code matches NO: ID code differs | - |
| C Code Difference | Challenge code/YES or NO | YES: Challenge code matches NO: Challenge code differs | - |
| Engine Start Condition | Engine start condition by certification ECU (smart key ECU assembly)/OK or NG | OK: Engine start permitted NG: Engine start prohibited | - |
| S Code Check | S code certification result/NG or OK | OK: S code certification result normal NG: S code certification result abnormal | - |
| L Code Check | L code certification result/NG or OK | OK: L code certification result normal NG: L code certification result abnormal | - |
| Ignition Available Area | Key area where engine start is possible/All or Front | All: All areas Front: Front only | - |
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Indicator for Lighting | Indicator illumination | ON/OFF | - |
| Indicator Condition | Indicator light illumination pattern | Green/Amber/No Sig | - |
| P Supply for Steering Lock | Steering lock ECU power supply | ON/OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Fr-Seat Inside Transmitter | Indoor key antenna (for front) | ON/OFF | - |
| Rr-Seat Inside Transmitter | Indoor key antenna (for rear1) | ON/OFF | - |
| Inside Trunk/Backdoor Transmitter | Indoor key antenna (for rear2) | ON/OFF | - |
| Outside Trunk/Backdoor Transmitter | Electrical key antenna | ON/OFF | - |