DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK POWER DOOR LOCK OPERATION
READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)
CHECK HARNESS AND CONNECTOR (REAR DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE)
INSPECT REAR DOOR OUTSIDE HANDLE RH
REPLACE DOOR ELECTRICAL KEY OSCILLATOR
CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
ENTRY AND START SYSTEM (for Entry Function) - Rear Door RH Entry Lock Function does not Operate
DESCRIPTION
If the rear door RH entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → rear door outside handle RH (entry lock switch) → rear door electrical key oscillator RH).
- For vehicles with entry function for rear doors.
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM ()
|
|
|
| 2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
for LHD
Main Body| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| PR Door Lock Position SW | Passenger side rear door lock position switch signal / ON or OFF | ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked | - |
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
for RHD
Main Body| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| DR Door Lock Position SW | Driver side rear door lock position switch signal / ON or OFF | ON: Driver side rear door unlocked
OFF: Driver side rear door locked | - |
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door RH LOCK/UNLOCK Functions do not Operate) ()
|
|
|
| 3.READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH) |
Using the intelligent tester, read the Data List.
for LHD
Entry & Start| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Pr-Door Trigger Switch | Passenger side rear door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed | - |
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
for RHD
Entry & Start| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Dr-Door Trigger Switch | Driver side rear door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed | - |
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
| OK | |
| |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
| 4.CHECK HARNESS AND CONNECTOR (REAR DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the z26 oscillator connector.
Disconnect the z25 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| z26-9 (TRG-) - z25-1 (TRG-) | Always | Below 1 Ω |
| z26-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE) |
Disconnect the E30 ECU connector.
Disconnect the z25 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
| Tester Connection | Condition | Specified Condition |
| E30-26 (TSW4) - z25-3 (TRG+) | Always | Below 1 Ω |
| E30-26 (TSW4) - Body ground | Always | 10 kΩ or higher |
- for RHD:
| Tester Connection | Condition | Specified Condition |
| E30-25 (TSW3) - z25-3 (TRG+) | Always | Below 1 Ω |
| E30-25 (TSW3) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 6.INSPECT REAR DOOR OUTSIDE HANDLE RH |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Switch Condition | Specified Condition |
| z25-1 (TRG-) - z25-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
| | REPLACE REAR DOOR OUTSIDE HANDLE ()
|
|
|
| 7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator ().
| 8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
| | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
|
| OK | |
| |
| END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE) |
|
