DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK POWER DOOR LOCK OPERATION
READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)
CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE)
INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side)
REPLACE DOOR ELECTRICAL KEY OSCILLATOR
CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
ENTRY AND START SYSTEM (for Entry Function) - Front Passenger Side Door Entry Lock Function does not Operate
DESCRIPTION
If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle (entry lock switch) → front passenger side door electrical key oscillator).
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM ()
|
|
|
| 2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| P Door Lock Position SW | Front passenger side door lock position switch signal / ON or OFF | ON: Front passenger side door unlocked
OFF: Front passenger side door locked | - |
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) ()
|
|
|
| 3.READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH) |
Using the intelligent tester, read the Data List.
Entry & Start| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| P-Door Trigger Switch | Front passenger side door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed | - |
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
| OK | |
| |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
| 4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the z22 or z24 oscillator connector.
Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
| Tester Connection | Condition | Specified Condition |
| z22-9 (TRG-) - z21-1 (TRG-) | Always | Below 1 Ω |
| z22-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
- for RHD:
| Tester Connection | Condition | Specified Condition |
| z24-9 (TRG-) - z23-1 (TRG-) | Always | Below 1 Ω |
| z24-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the E29 ECU connector.
Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
| Tester Connection | Condition | Specified Condition |
| E29-4 (TSW2) - z21-3 (TRG+) | Always | Below 1 Ω |
| E29-4 (TSW2) - Body ground | Always | 10 kΩ or higher |
- for RHD:
| Tester Connection | Condition | Specified Condition |
| E29-4 (TSW2) - z23-3 (TRG+) | Always | Below 1 Ω |
| E29-4 (TSW2) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 6.INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side) |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
| Tester Connection | Switch Condition | Specified Condition |
| z21-1 (TRG-) - z21-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
- for RHD:
| Tester Connection | Switch Condition | Specified Condition |
| z23-1 (TRG-) - z23-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
| | REPLACE FRONT DOOR OUTSIDE HANDLE ()
|
|
|
| 7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator ().
| 8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
| | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
|
| OK | |
| |
| END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE) |
|
