DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK POWER DOOR LOCK OPERATION
CHECK VEHICLE EQUIPMENT
CHECK POWER BACK DOOR OPERATION
READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
READ VALUE USING INTELLIGENT TESTER (BACK DOOR LOCK SWITCH)
CHECK BACK DOOR OPENER SWITCH
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BACK DOOR OPENER SWITCH)
ENTRY AND START SYSTEM (for Entry Function) - Back Door Entry Lock Function does not Operate
DESCRIPTION
If the back door entry lock function does not operate but the back door open function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be the entry lock switch circuit (certification ECU (smart key ECU assembly) → back door opener switch).
WIRING DIAGRAM
INSPECTION PROCEDURE
- Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".
| 1.CHECK POWER DOOR LOCK OPERATION |
When the door control switch of the master switch assembly is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM ()
|
|
|
| 2.CHECK VEHICLE EQUIPMENT |
Check if the power back door is equipped on the vehicle.
Result| Result | Proceed to |
| w/ Power Back Door System | A |
| w/o Power Back Door System | B |
| 3.CHECK POWER BACK DOOR OPERATION |
When the power back door switch is operated, check that the power back door closes.
- OK:
- Power back door system is normal.
Result| Result | Proceed to |
| Power back door system is abnormal | A |
| Power back door system is normal | B |
| A | |
| |
| GO TO POWER BACK DOOR SYSTEM ()
|
|
| 4.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Back Lock Pos switch | Back door lock position switch signal / ON or OFF | ON: Back door is unlocked
OFF: Back door is locked | - |
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
| | GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door LOCK/UNLOCK Functions do not Operate) ()
|
|
|
| 5.READ VALUE USING INTELLIGENT TESTER (BACK DOOR LOCK SWITCH) |
Using the intelligent tester, read the Data List.
Entry&Start| Tester Display | Measurement Item/Display | Normal Condition | Diagnostic Note |
| Tr/B-Door Lock SW | Back door lock switch / ON or OFF | ON: Back door lock switch is pushed
OFF: Back door lock switch is not pushed | - |
- OK:
- "ON" (switch is pushed) and "OFF" (switch is not pushed) appears on the screen.
| OK | |
| |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
| 6.CHECK BACK DOOR OPENER SWITCH |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Switch Condition | Specified Condition |
| 1 (UL) - 2 (L) | Lock switch pushed | Below 1 Ω |
| 1 (UL) - 2 (L) | Lock switch not pushed | 10 kΩ or higher |
| | REPLACE BACK DOOR OPENER SWITCH ()
|
|
|
| 7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BACK DOOR OPENER SWITCH) |
Disconnect the E29 ECU connector.
Disconnect the S7 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| E29-7 (TSW5) - S7-1 (UL) | Always | Below 1 Ω |
| E29-7 (TSW5) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
|
