DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK REGISTRATION MODE
CHECK SECURITY INDICATOR LIGHT OPERATION
READ VALUE USING INTELLIGENT TESTER
KEY REGISTRATION
INSPECT UNLOCK WARNING SWITCH ASSEMBLY
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)
INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System) - Key Cannot be Registered
DESCRIPTION
A maximum of 5 master key codes and 3 sub key codes can be registered.
WIRING DIAGRAM
Refer to "System Diagram" ().
INSPECTION PROCEDURE
- When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.
1.CHECK REGISTRATION MODE |
Check that the system enters registration mode.
- OK:
- System enters registration mode
2.CHECK SECURITY INDICATOR LIGHT OPERATION |
In registration mode, when the key is inserted in the ignition key cylinder, check that the security indicator light blinks in the normal pattern shown below.
- If the new key code registration fails, code 2-1 will be output through the security indicator light. Trying to reregister an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown below.
ResultResult | Proceed to |
Code 2-1 or Code 2-3 | A |
Code 2-2 | B |
| REGISTRATION AS ANOTHER KEY |
|
|
3.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Immobiliser / Data List.
According to the display on the intelligent tester, read the Data List.
ImmobiliserTester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Transponder S-code | Number of registered sub-keys / min.: 0, max.: 3 | Number of registered sub-keys | - |
Transponder M-code | Number of registered master keys / min.: 0, max.: 5 | Number of registered master keys | - |
ResultResult | Proceed to |
None of the following | A |
Registered master keys: 5, registered sub-keys: 0 | B |
Registered master keys: 0, registered sub-keys: 3 | C |
Registered master keys: 5, registered sub-keys: 3 | D |
| KEY REGISTRATION (SUB-KEY) |
|
|
| KEY REGISTRATION (MASTER KEY) |
|
|
| |
|
Refer to the table below to determine if additional keys can be registered.
Number of Keys Registered (Master and Sub) | Proceed to |
0 | New key ID registration (refer to the Service Bulletin) |
1 to 7 | Additional key ID registration (refer to the Service Bulletin) |
Check whether key registration.
| REPLACE TRANSPONDER KEY ECU ASSEMBLY |
|
|
OK | |
| |
END (KEY IS MALFUNCTIONING) |
|
5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
Inspect the unlock warning switch assembly ().
| REPLACE UNLOCK WARNING SWITCH ASSEMBLY ()
|
|
|
6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH) |
Disconnect the E94 unlock warning switch assembly connector.
Disconnect the E96 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
E94-1 (UN+) - E96-3 (KSW) | Always | Below 1 Ω |
E94-2 (UN-) - Body ground | Always | Below 1 Ω |
E94-1 (UN+) - Body ground | Always | 10 kΩ or higher |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY |
Inspect the front door courtesy light switch assembly ().
| REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY ()
|
|
|
8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY) |
for LHD:
Disconnect the K2 front door courtesy light switch assembly connector.
Disconnect the E96 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
K2-1 - E96-7 (CTY) | Always | Below 1 Ω |
K2-1 - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the L1 front door courtesy light switch assembly connector.
Disconnect the E96 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
L1-1 - E96-7 (CTY) | Always | Below 1 Ω |
L1-1 - Body ground | Always | 10 kΩ or higher |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
OK | |
| |
REPLACE TRANSPONDER KEY ECU ASSEMBLY |
|