Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUPPLEMENTAL RESTRAINT SYSTEMS


AIRBAG SYSTEM - DTC CHECK / CLEAR

CHECK DTC (Using SST Check Wire)
Airbag System - Dtc Check / Clear. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Check the DTCs (Present trouble code).

Turn the ignition switch to ON, and wait for approximately 60 seconds.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

  • SST
  • 09843-18040
  • NOTICE:
  • Connect the correct terminals to avoid a malfunction.

Check the DTCs (Past trouble code).

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

  • SST
  • 09843-18040
  • NOTICE:
  • Connect the correct terminals to avoid a malfunction.

Turn the ignition switch to ON, and wait for approximately 60 seconds.

Airbag System - Dtc Check / Clear. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Read the DTCs.

Read the blinking patterns of the DTCs. As examples, the blinking patterns for the normal system code and trouble codes 11 and 31 are shown in the illustration.

Normal system code indication (without past trouble code):
The light blinks twice per second.
Normal system code indication (with past trouble code):
When a past trouble code is stored in the center airbag sensor, the light blinks only once per second.
Trouble code indication:
Each digit of a DTC is separated by a 1.5 second pause.

If there is more than 1 code, there will be a 2.5 second pause between each code. After all codes are shown, there will be a 4.0 second pause, and then all codes will be repeated.


  • HINT:
If 2 or more malfunctions are found, the indication begins with the smaller-numbered code.
If DTCs are output without connecting the terminals, proceed to "Diagnosis Circuit" ().
CLEAR DTC (Using SST Check Wire)

When the ignition switch is turned off, the DTCs are cleared.

  • HINT:
  • Depending on the DTC, the code may not be cleared by turning off the ignition switch. In this case, proceed to the next procedure.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3, and then turn the ignition switch to ON.

  • SST
  • 09843-18040

Disconnect terminal TC of the DLC3 within 3 to 10 seconds after the DTCs are output, and check if the SRS warning light comes on after 3 seconds.

Within 2 to 4 seconds after the SRS warning light comes on, connect terminals 13 (TC) and 4 (CG) of the DLC3.

The SRS warning light should go off within 2 to 4 seconds after connecting terminals 13 (TC) and 4 (CG) of the DLC3. Then, disconnect terminal 13 (TC) within 2 to 4 seconds after the SRS warning light goes off.

The SRS warning light comes on again within 2 to 4 seconds after disconnecting terminal 13 (TC). Then, reconnect terminals 13 (TC) and 4 (CG) within 2 to 4 seconds after the SRS warning light comes on.

Check if the SRS warning light goes off within 2 to 4 seconds after connecting terminals 13 (TC) and 4 (CG) of the DLC3. Also check if the normal system code is output within 1 second after the SRS warning light goes off.


If DTCs are not cleared, repeat this procedure until the codes are cleared.

Airbag System - Dtc Check / Clear. SUPPLEMENTAL RESTRAINT SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

CHECK DTC (Using the Intelligent Tester)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Check the DTCs by following the prompts on the tester screen.

  • HINT:
  • Refer to the intelligent tester operator's manual for further details.
CLEAR DTC (Using the Intelligent Tester)

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Clear the DTCs by following the prompts on the tester screen.

  • HINT:
  • Refer to the intelligent tester operator's manual for further details.
SUPPLEMENTAL RESTRAINT SYSTEMS
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
AIRBAG SYSTEM