Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - HEATING / AIR CONDITIONING
AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) - DATA LIST / ACTIVE TEST
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ambient Temp Sensor | Cooler thermistor (ambient temperature sensor) / Min.: -23.3°C (-9.94°F) Max.: 65.95°C (150.71°F) | Actual ambient temperature displayed | Open in the circuit: -23.3°C (-9.94°F). Short in the circuit: 65.95°C (150.71°F). |
| Adjusted Ambient Temp | Adjusted ambient temperature / Min.: -30.8°C (-23.44°F) Max.: 50.8°C (123.44°F) | Adjusted ambient temperature displayed | - |
| Evaporator Fin Thermistor | No. 1 cooler thermistor / Min.: -29.7°C (-21.46°F) Max.: 59.55°C (139.19°F) | Actual evaporator temperature displayed | Open in the circuit: -29.7°C (-21.46°F). Short in the circuit: 59.55°C (139.19°F). |
| Engine Coolant Temp | Engine coolant temperature / Min.: 1.3°C (34.34°F) Max.: 90.55°C (194.99°F) | Actual engine coolant temperature displayed while engine warmed up | - |
| Blower Motor Speed Level | Blower with fan motor sub-assembly speed level / Min.: 0 level, Max.: 31 level | Increases in range between 0 and 31 as blower with fan motor sub-assembly speed increases | - |
| Regulator Pressure Sensor | Air conditioner pressure sensor / Min.: -0.4566 MPaG Max.: 3.2943 MPaG | Actual refrigerant pressure displayed | - |
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) target pulse / Min.: 0, Max.: 255 | for LHD MAX. COOL: 90 (pulse) MAX. HOT: 8 (pulse) for RHD MAX. COOL: 8 (pulse) MAX. HOT: 90 (pulse) | - |
| Air Outlet Servo Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) target pulse / Min.: 0, Max.: 255 | FACE: 117 (pulse) B/L: 93 (pulse) FOOT: 41 (pulse) F/D: 18 (pulse) DEF: 6 (pulse) | - |
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly target pulse / Min.: 0, Max.: 255 | for LHD Recirculation: 37 (pulse) Fresh: 9 (pulse) for RHD Recirculation: 9 (pulse) Fresh: 37 (pulse) | - |
| Cool Air Bypass Pulse | No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) target pulse / Min.: 0, Max.: 255 | Shut and DEF mode: 6 (pulse) Shut: 28 (pulse) Open: 57 (pulse) | - |
| Electric Heater Count* | Number of electrical heaters operating / Min.: 0, Max.: 3 | Actual heater counts displayed | - |
| Ambient Temperature Shift | Ambient temperature shift / +3 C, +2 C, +1 C, NORMAL, -1 C, -2 C, -3 C | Customized value displayed | - |
| Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 | Number of DTCs displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/C Signal | Air conditioning signal / ON or OFF | ON: A/C switch on OFF: A/C switch off | - |
*: w/ PTC Heater
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Blower Motor | Blower with fan motor sub-assembly | Min.: 0, Max.: 31 | - |
| Magnetic Clutch Relay | Magnet clutch relay | OFF or ON | - |
| Heater Active Level* | Quick heater assembly | Min.: 0, Max.: 3 | |
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) | Min.: 0, Max.: 255 | - |
| Air Outlet Servo Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) | Min.: 0, Max.: 255 | - |
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly | Min.: 0, Max.: 255 | - |
| Cool Air Bypass Pulse | No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) | Min.: 0, Max.: 255 | - |
*: w/ PTC Heater