Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WINDOW / GLASS
POWER WINDOW REGULATOR MOTOR (for Rear Door) - INSPECTION
- HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
| 1. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows) |
Apply positive (+) battery voltage to the connector terminal 2 (B).
- NOTICE:
- Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.
Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition Specified Condition Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.Motor gear rotates clockwise (Up) Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.Motor gear rotates counterclockwise (Down)
If the result is not as specified, replace the rear power window regulator motor assembly LH.
- CAUTION:
- Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.
| *1 | Motor Gear |
| *a | Component without harness connected (Front Power Window Regulator Motor Assembly LH) |
| *b | Clockwise |
| *c | Counterclockwise |
| 2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows) |
Apply positive (+) battery voltage to the connector terminal 2 (B).
- NOTICE:
- Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.
Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition Specified Condition Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.Motor gear rotates counterclockwise (Up) Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.Motor gear rotates clockwise (Down)
If the result is not as specified, replace the rear power window regulator motor assembly RH.
- CAUTION:
- Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.
| *1 | Motor Gear |
| *a | Component without harness connected (Front Power Window Regulator Motor Assembly RH) |
| *b | Clockwise |
| *c | Counterclockwise |
| 3. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only) |
Check the operation of the regulator motor.
Apply battery voltage to the regulator motor and check the operation of the regulator motor.
- OK:
Measurement Condition Specified Condition Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2Motor gear rotates clockwise Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1Motor gear rotates counterclockwise
If the result is not as specified, replace the rear power window regulator motor assembly LH.
| *1 | Motor Gear |
| *a | Component without harness connected (Rear Power Window Regulator Motor Assembly LH) |
| *b | Clockwise |
| *c | Counterclockwise |
| 4. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only) |
Check the operation of the regulator motor.
Apply battery voltage to the regulator motor and check the operation of the regulator motor.
- OK:
Measurement Condition Specified Condition Battery positive (+)→Terminal 2
Battery negative (-)→Terminal 1Motor gear rotates clockwise Battery positive (+)→Terminal 1
Battery negative (-)→Terminal 2Motor gear rotates counterclockwise
If the result is not as specified, replace the rear power window regulator motor assembly RH.
| *1 | Motor Gear |
| *a | Component without harness connected (Front Rear Window Regulator Motor Assembly RH) |
| *b | Clockwise |
| *c | Counterclockwise |