Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WINDOW / GLASS
POWER WINDOW REGULATOR MOTOR (for Front Door) - REMOVAL
- HINT:
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 3. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH |
Detach the clip and claw, and remove the front door lower frame bracket garnish LH.
| 4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL |
Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape |
| 5. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY |
Using a moulding remover, detach the 5 claws.
Disconnect the connector and remove the armrest base panel.
| 6. REMOVE DOOR ASSIST GRIP COVER |
Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.
| 7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Remove the 3 screws.
Remove the 13 clips.
Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.
- HINT:
- Make sure that the pin labeled A in the illustration is detached from the door panel.
Disconnect the connector.
Disconnect the 2 cables from the front door inside handle sub-assembly LH.
| 8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
Disconnect the speaker connector.
Remove the 4 screws and speaker.
- NOTICE:
- Do not touch the cone part of the speaker.
| 9. REMOVE FRONT DOOR SERVICE HOLE COVER |
Using a clip remover, detach the 9 clamps.
Remove the bolt and disconnect the 2 connectors.
Remove the front door service hole cover LH.
- HINT:
- Remove the remaining tape on the door.
| 10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
Driver Side:
Temporarily install the multiplex network master switch.
Passenger Side:
Temporarily install the power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly until the bolts appear in the service holes.
Disconnect the cable from the negative (-) battery terminal.
Remove the 2 bolts.
- NOTICE:
- Be careful when removing the bolts as the glass may fall and become damaged.
Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.
- HINT:
- Remove the front door glass sub-assembly upward.
- NOTICE:
- Be careful not to damage the glass.
Driver Side:
Remove the multiplex network master switch.
Passenger Side:
Remove the power window regulator switch assembly.
| 11. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts, and front door window regulator sub-assembly LH.
- HINT:
- Remove the front door window regulator sub-assembly LH through the service hole.
- NOTICE:
- Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.
Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.
Remove the temporary bolt from the front door window regulator sub-assembly LH.
| 12. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Using a T25 "TORX" driver, remove the 3 screws and motor.
- NOTICE:
- Be careful when removing the screws as the motor may fall and become damaged.
| *A | for Models with Jam Protection Function on 4 Windows |
| *B | for Front Passenger Side, for Models with Jam Protection Function on Driver Door Window Only |