Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WINDOW / GLASS
POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Driver Door Window Only) - DATA LIST / ACTIVE TEST
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Auto SW | Driver side power window auto up/down signal / ON or OFF | ON: Driver side power window auto up/down switch on multiplex network master switch operated OFF: Driver side power window switch on multiplex network master switch not operated | - |
| P Door P/W Up SW | Front passenger side power window remote manual up signal / ON or OFF | ON: Front passenger side power window remote manual up switch on multiplex network master switch operated OFF: Front passenger side power window switch on multiplex network master switch not operated | - |
| RR Door P/W up switch | Rear power window RH remote manual up signal / ON or OFF | ON: Rear power window RH remote manual up switch on multiplex network master switch operated OFF: Rear power window switch RH on multiplex network master switch not operated | - |
| RL Door P/W up switch | Rear power window LH remote manual up signal / ON or OFF | ON: Rear power window LH remote manual up switch on multiplex network master switch operated OFF: Rear power window switch LH on multiplex network master switch not operated | - |
| P Door P/W Down SW | Front passenger side power window remote manual down signal / ON or OFF | ON: Front passenger side power window remote manual down switch on multiplex network master switch operated OFF: Front passenger side power window switch on multiplex network master switch not operated | - |
| RR Door P/W Down SW | Rear power window RH remote manual down signal / ON or OFF | ON: Rear power window RH remote manual down switch on multiplex network master switch operated OFF: Rear power window switch RH on multiplex network master switch not operated | - |
| RL Door P/W Down SW | Rear power window LH remote manual down signal / ON or OFF | ON: Rear power window LH remote manual down switch on multiplex network master switch operated OFF: Rear power window switch LH on multiplex network master switch not operated | - |
| Window Lock Switch Status | Power window lock switch / ON or OFF | ON: Power window lock switch on OFF: Power window lock switch off | - |
| Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Auto SW | Driver side power window auto up/down signal / ON or OFF | ON: Driver side power window auto up/down switch operated OFF: Driver side power window switch not operated | - |
| D Door P/W Up SW | Driver side power window manual up signal / ON or OFF | ON: Driver side power window manual up switch operated OFF: Driver side power window switch not operated | - |
| D Door P/W Down SW | Driver side power window manual down signal / ON or OFF | ON: Driver side power window manual down switch operated OFF: Driver side power window switch not operated | - |
| Glass Position (Close-1/4) | Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution | OK: Motor normally operates between fully closed to 1/4 open position Caution: Jam protection function operates due to detection of foreign object or irregular movement | - |
| Glass Position (1/4-2/4) | Jam protection status of window glass within range of 1/4 to 1/2 open position / OK or Caution | OK: Motor normally operates between 1/4 to 1/2 open position Caution: Jam protection function operates due to detection of foreign object or irregular movement | - |
| Glass Position (2/4-3/4) | Jam protection status of window glass within range of 1/2 to 3/4 open position / OK or Caution | OK: Motor normally operates between 1/2 to 3/4 open position Caution: Jam protection function operates due to detection of foreign object or irregular movement | - |
| Glass Position (3/4-Open) | Jam protection status of window glass within range of 3/4 to fully open position / OK or Caution | OK: Motor normally operates between 3/4 to fully open position Caution: Jam protection function operates due to detection of foreign object or irregular movement | - |
| Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 | Number of DTCs will displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Communication D-Door Motor | Connection status between power window regulator motor (for driver side) and main body ECU / OK or Stop | OK: Connection Stop: No connection | - |
| D Door Courtesy SW | Driver side door courtesy signal / ON or OFF | ON: Driver door open OFF: Driver door closed | - |
| P Door Courtesy SW | Front passenger side door courtesy signal / ON or OFF | ON: Front passenger door open OFF: Front passenger door closed | - |
| RL Door Courtesy SW | Rear LH side door courtesy signal / ON or OFF | ON: Rear LH side door open OFF: Rear LH side door closed | - |
| RR Door Courtesy SW | Rear RH side door courtesy signal / ON or OFF | ON: Rear RH side door open OFF: Rear RH side door closed | - |
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
- CAUTION:
- Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Driver side power window | OFF/UP/DOWN | - |