Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM
FRONT BUMPER (for Standard) - DISASSEMBLY
| 1. REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System) |
Remove the 4 clamps and headlight cleaner hose.
Disconnect the headlight cleaner hose.
| *A | for LH Side |
| *B | for RH Side |
| 2. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System) |
Extend the type 1 headlight washer nozzle sub-assembly LH.
Detach the 2 claws and remove the type 1 headlight washer nozzle sub-assembly LH.
| 3. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System) |
- HINT:
- Use the same procedure described for the LH side.
| 4. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) |
Remove the bolt.
Detach the 2 claws and remove the headlight washer actuator sub-assembly LH.
| 5. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System) |
- HINT:
- Use the same procedure described for the LH side.
| 6. REMOVE NO. 4 ENGINE ROOM WIRE |
w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
Remove the No. 4 engine room wire.
Disconnect the 2 connectors.
Detach the 11 clamps and remove the No. 4 engine room wire.
w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
Remove the No. 4 engine room wire.
Disconnect the 4 connectors.
Detach the 12 clamps and remove the No. 4 engine room wire.
w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
Remove the No. 4 engine room wire.
Disconnect the 2 connectors.
Detach the 12 clamps and remove the No. 4 engine room wire.
| 7. REMOVE ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System) |
Detach the 4 claws and remove the ultrasonic sensor clip.
| 8. REMOVE NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System) |
- HINT:
- Use the same procedure to remove the No. 1 ultrasonic sensor on the other side.
While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the No. 1 ultrasonic sensor.
- HINT:
- The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the No. 1 ultrasonic sensor.
| 9. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System) |
- HINT:
- Use the same procedure to remove the No. 2 ultrasonic sensor retainer on the other side.
Detach the 2 claws and remove the No. 2 ultrasonic sensor retainer from the front bumper cover.
| 10. REMOVE FRONT BUMPER INNER BRACKET (w/ Fog Light) |
Detach the 3 claws and remove the front bumper inner bracket.
| 11. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light) |
Remove the 2 screws.
 | Screw |
 | Connector |
Detach the 2 guides and remove the fog light assembly LH.
Disconnect the connector.
| 12. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light) |
- HINT:
- Use the same procedure described for the LH side.
| 13. REMOVE FRONT BUMPER HOLE COVER LH (w/ Fog Light) |
Remove the 2 retainers and the 2 screws.
Detach the 5 claws and remove the front bumper hole cover LH.
| 14. REMOVE FRONT BUMPER HOLE COVER RH (w/ Fog Light) |
- HINT:
- Use the same procedure described for the LH side.
| 15. REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light) |
Remove the 2 retainers and the screw.
Detach the 5 claws and remove the front bumper hole cover LH.
| 16. REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light) |
- HINT:
- Use the same procedure described for the LH side.
| 17. REMOVE LOWER NO. 1 RADIATOR GRILLE |
Remove the 4 retainers.
Detach the 16 claws and remove the lower No. 1 radiator grille.
| *1 | Retainer | - | - |
| 18. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket) |
Remove the 2 bolts.
Detach the 2 claws and remove the front bumper extension mounting bracket.
| 19. REMOVE FRONT BUMPER GUARD (w/ Garnish) |
Remove the 4 nuts.
Detach the 6 clips and remove the front bumper guard.
| 20. REMOVE FRONT NO. 2 BUMPER PROTECTOR |
Remove the 2 front No. 2 bumper protectors.