Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - TIRE PRESSURE MONITORING

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CAN COMMUNICATION LINE

CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

INSPECT DLC3 (TC VOLTAGE)

TIRE PRESSURE WARNING SYSTEM - TC and CG Terminal Circuit

DESCRIPTION

DTC output mode is set by connecting terminals 13 (TC) and 4 (CG) of the DLC3. The DTCs are indicated by the tire pressure warning light blinking pattern.


WIRING DIAGRAM

Tire Pressure Warning System - Tc And Cg Terminal Circuit. TIRE PRESSURE MONITORING. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

  • HINT:
  • If the tire pressure warning light blinks continuously, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION LINE

Turn the engine switch off.

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the GTS on.

Enter the following menus: "CAN Bus Check" from the "System Select" screen.

Check the CAN communication system (for LHD: , for RHD: ).

  • OK:
  • The CAN communication system is normal.
  • Result:
  • ResultProceed to
    OKA
    NG (for LHD)B
    NG (for RHD)C
B
GO TO CAN COMMUNICATION SYSTEM ()
C
GO TO CAN COMMUNICATION SYSTEM ()
A
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

Disconnect the ECM A38*1, A52*2 connector.

*1: for LHD
*2: for RHD

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • for LHD
    Tester ConnectionConditionSpecified Condition
    E22-13 (TC) - A38-16*1, 27*2(TC)AlwaysBelow 1 Ω
    E22-13 (TC) or A38-16*1, 27*2(TC) - Body groundAlways10 kΩ or higher
    E22-4 (CG) - Body groundAlwaysBelow 1 Ω
*1: for 1UR-FE
*2: for 1VD-FTV
  • Standard Resistance:
  • for RHD
    Tester ConnectionConditionSpecified Condition
    E22-13 (TC) - A52-27 (TC)AlwaysBelow 1 Ω
    E22-13 (TC) or A52-27 (TC) - Body groundAlways10 kΩ or higher
    E22-4 (CG) - Body groundAlwaysBelow 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
3.INSPECT DLC3 (TC VOLTAGE)
Tire Pressure Warning System - Tc And Cg Terminal Circuit. TIRE PRESSURE MONITORING. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Connect the ECM A38*1, A52*2 connector.

*1: for LHD
*2: for RHD

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionSwitch ConditionSpecified Condition
    E22-13 (TC) - E22-4 (CG)Engine switch on (IG)11 to 14 V
Text in Illustration
*aFront view of DLC3
  • Result:
  • ResultProceed to
    OKA
    NG (for 1UR-FE)B
    NG (for 1VD-FTV)C
B
REPLACE ECM ()
C
REPLACE ECM ()
A
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE ()