Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUSPENSION CONTROL
SUSPENSION CONTROL ECU - INSTALLATION
| 1. INSTALL SUSPENSION CONTROL ECU |
Attach the wire harness clamp and connect the connector.
Install the ECU with the 2 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}
| 2. INSTALL REAR SIDE NO. 2 AIR DUCT (w/ Heater) |
Install the duct with the 3 screws.
- Torque:
- 5.4 N*m{ 55 kgf*cm, 48 in.*lbf}
| 3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
- HINT:
- When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
- Torque:
- 12 N*m{ 122 kgf*cm, 9 ft.*lbf}
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Tonneau Cover:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the screw and clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
Attach the 3 claws to install the cover.
| 4. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type) |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 5. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover) |
- HINT:
- Use the same procedure to install the tonneau cover holder cap on the other side.
Attach the 2 claws to install the tonneau cover holder cap.
| 6. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE |
Attach the 6 clips to install the support plate.
| 7. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
| 8. INSTALL REAR STEP COVER |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 9. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type) |
Install the rear No. 2 seat assembly LH ().
| 10. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 11. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type) |
Install the rear No. 2 seat assembly LH ().
| 12. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type) |
- HINT:
- Use the same procedures described for the LH side.
| 13. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 15. PERFORM VEHICLE HEIGHT OFFSET CALIBRATION |
Perform the vehicle height offset calibration ().
| 16. PERFORM ZERO POINT CALIBRATION OF G SENSOR |
Perform the zero point calibration of G sensor ().
| 17. ADJUST HEADLIGHT ASSEMBLY |
for Standard:
Adjust the headlight ().
for HID Headlight:
Adjust the headlight ().