Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUSPENSION CONTROL
FRONT ACCELERATION SENSOR - REMOVAL
| 1. TABLE OF BOLT, SCREW AND NUT |
- HINT:
- All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION |
Place protective tape as shown in the illustration.
Using a moulding remover, detach the 7 claws and remove the panel cushion.
| 4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH |
Remove the clip.
Remove the screw.
Detach the 8 claws.
Remove the panel pad and disconnect the connectors and 2 clamps.
| 5. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION |
Put protective tape around the No. 1 instrument panel finish panel cushion.
| *1 | Protective Tape |
Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.
| 6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH |
Remove the clip and screw.
Detach the 7 claws and remove the lower instrument panel pad sub-assembly.
| 7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
Detach the 7 claws.
Disconnect the connectors and remove the lower center instrument cluster finish panel sub-assembly.
| 8. REMOVE INSTRUMENT SIDE PANEL LH |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
| 9. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.
| 10. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Place protective tape as shown in the illustration.
Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.
| *A | w/ Entry and Start System | *B | w/o Entry and Start System |
| *1 | Protective Tape | - | - |
| 11. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
Remove the 2 screws.
Detach the 3 claws.
Disconnect the connectors and remove the No. 1 instrument panel under cover.
| 12. REMOVE FRONT DOOR SCUFF PLATE LH |
Detach the 7 claws and 4 clips, and remove the scuff plate.
| 13. REMOVE COWL SIDE TRIM BOARD LH |
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
| 14. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Using a screwdriver, detach the 2 claws and open the hole cover.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape |
w/ Driver Side Knee Airbag:
Remove the 2 bolts.
Detach the 16 claws.
w/o Driver Side Knee Airbag:
Remove the 2 bolts.
Detach the 9 claws.
for Automatic Air Conditioning System:
Detach the 2 claws and remove the room temperature sensor.
Detach the 2 claws and disconnect the 2 control cables.
Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.
| 15. REMOVE NO. 1 SWITCH HOLE BASE |
Detach the 4 claws.
Disconnect the connectors and remove the No. 1 switch hole cover.
| 16. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
Remove the 5 bolts and driver side knee airbag.
Disconnect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
| 17. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
Detach the 2 claws and disconnect the DLC3.
Remove the 5 bolts and lower instrument panel.
| 18. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch) |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
| 19. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch) |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 6 claws.
Disconnect the connector and remove the instrument side panel.
| 20. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
Detach the 4 claws and remove the No. 2 instrument panel under cover.
| 22. REMOVE COWL SIDE TRIM BOARD RH |
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
| 23. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag) |
Remove the 4 bolts.
Detach the 4 claws and remove the front passenger side knee airbag.
Disconnect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
| 24. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag) |
Remove the 2 bolts.
Detach the 4 claws and remove the lower instrument panel.
| 25. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.
| 26. REMOVE INSTRUMENT PANEL BOX DOOR KNOB |
Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.
| 27. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
Remove the 4 bolts.
Detach the 3 claws.
Disconnect the connector and remove the lower No. 2 instrument panel finish panel.
| 28. REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for LHD) |
Vehicle rear side:
Disconnect the 7 connectors.
Detach the 2 clamps.
Remove the bolt and 2 nuts.
Vehicle front side:
Disconnect the 5 connectors.
Remove the steering control ECU with junction block from the vehicle.
| 29. REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for RHD) |
Vehicle rear side:
Disconnect the 2 connectors.
Remove the bolt and 2 nuts.
Vehicle front side:
Disconnect the connector.
Remove the steering control ECU with junction block from the vehicle.
| 30. REMOVE ACCELERATION SENSOR (for Driver Side) |
Disconnect the connector.
Remove the bolt and sensor.
- HINT:
- Use the same procedures for LHD and RHD vehicles.
| 31. REMOVE ACCELERATION SENSOR (for Front Passenger Side) |
Disconnect the connector.
Remove the bolt and sensor.
- HINT:
- Use the same procedures for LHD and RHD vehicles.