INSTALL HEIGHT CONTROL PUMP AND MOTOR ASSEMBLY

INSTALL HEIGHT CONTROL TUBE CLAMP

CONNECT REAR NO. 6 HEIGHT CONTROL TUBE

BLEED AIR FROM SUSPENSION FLUID

CHECK FLUID LEVEL IN RESERVOIR

INSPECT FOR SUSPENSION FLUID LEAK

INSTALL FUEL TANK FILLER PIPE PROTECTOR

INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

INSTALL REAR BUMPER COVER

INSTALL REAR QUARTER PANEL MUDGUARD RH

Install the pump and motor with the 3 bolts.

• Torque:
• 31 N*m{ 316 kgf*cm, 23 ft.*lbf}

Connect the 2 connectors and 3 clamps.

Install the tube clamp with the 2 bolts.

• Torque:
• 20 N*m{ 204 kgf*cm, 15 ft.*lbf}

Connect the reservoir hose to the tube clamp.

Using a union nut wrench, connect the control tube to the pump and motor.

• Torque:
• without union nut wrench:
• 15 N*m{ 155 kgf*cm, 11 ft.*lbf}
• with union nut wrench:
• 14 N*m{ 143 kgf*cm, 10 ft.*lbf}

• HINT:

With the engine stopped, fill the reservoir tank with fluid.

• NOTICE:

• When the engine starts, the pump operates and fluid is supplied to each cylinder from the reservoir tank. Therefore, add the necessary amount of fluid so that the reservoir tank does not become empty.

• HINT:

• At this point, the vehicle height is low because the pressure of the cylinders is low.

With the vehicle on a level surface, start the engine and set the vehicle height to NORMAL with the suspension control switch.

When the vehicle height becomes NORMAL and the pump stops, stop the engine.

Connect a hose to the bleeder plug of the front left side or right side control valve, then loosen the bleeder plug.

• CAUTION:

• Be careful when loosening the control valve bleeder plug because the front vehicle height drops rapidly.

After the fluid containing air stops coming out, retighten the bleeder plug.

• Torque:
• 8.3 N*m{ 85 kgf*cm, 73 in.*lbf}

• HINT:

• If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

Connect a hose to the bleeder plug of the rear left side or right side control valve, then loosen the bleeder plug.

• CAUTION:

• Be careful when loosening the control valve bleeder plug because the rear vehicle height drops rapidly.

After the fluid containing air stops coming out, retighten the bleeder plug.

• Torque:
• 8.3 N*m{ 85 kgf*cm, 73 in.*lbf}

• HINT:

• If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

Repeat the previous 4 procedures until the fluid containing air stop coming out.

With the vehicle empty, after setting the vehicle height to NORMAL from LO, check the indicator to make sure the vehicle height is NORMAL and check that the fluid level in the reservoir tank is within the specified range (MAX, MIN).

• HINT:

• After changing the vehicle height from LO to NORMAL, do not stop the engine for 25 seconds because the pressure control for the main accumulator is operating. After that, check the fluid level.

Check that the union nuts shown in the illustration are tightened to the specified torque.

• Torque:
• without union nut wrench:
• 15 N*m{ 155 kgf*cm, 11 ft.*lbf}
• with union nut wrench:
• 14 N*m{ 143 kgf*cm, 10 ft.*lbf}

• HINT:

Check for fluid leakage from the parts and connections.

• HINT:

• For union nuts and union bolts not shown in the illustration, refer to the installation procedures for each title.

Using a T30 "TORX" socket wrench, install the pipe protector with the 3 screws and grommet.

Install the new grommet.

Install the protector with 2 new grommets.

Install the 2 screws.

for Standard:

Install the bumper cover ().

w/ Towing Hitch:

Install the bumper cover ().

w/ Pintle Hook:

Install the bumper cover ().

for Double Swing Out Type:

Install the bumper cover ().

Install the mudguard with the clip.

Using a T30 "TORX" socket, install the 7 screws.