Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1GR-FE LUBRICATION

OIL LEVEL SENSOR - INSTALLATION

1. INSTALL ENGINE OIL LEVEL SENSOR

Install a new gasket to the engine oil level sensor.

Install the sensor with the 4 bolts.

  • Torque:
  • 10 N*m{ 102 kgf*cm, 7 ft.*lbf}

Connect the connector.

2. ADD ENGINE OIL

Add fresh oil.

  • NOTICE:
Oil Level Sensor - Installation. 1GR-FE LUBRICATION. Land Cruiser URJ200 URJ202 GRJ200 VDJ200
  • Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
  • If engine oil is on the location indicated by the arrow, replace the belt tensioner.
  • Standard Engine Oil:
  • Oil GradeOil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil15W-40
    20W-50
  • Standard Engine Oil (for China):
  • Oil GradeOil Viscosity (SAE)
    API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil0W-20
    5W-20
    5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil15W-40
    20W-50
  • Standard Oil Capacity:
  • ItemSpecified Condition
    Drain and refill without oil filter change5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Drain and refill with oil filter change6.1 liters (6.4 US qts, 5.4 Imp. qts)
    Dry fill7.1 liters (7.5 US qts, 6.2 Imp. qts)
3. INSPECT ENGINE OIL LEVEL

Warm up the engine, and then stop the engine and wait for 5 minutes.

Check that the engine oil level is between the low level and full level marks on the dipstick.


If low, check for leakage and add oil up to the full level mark.

  • NOTICE:
  • Do not fill engine oil above the full level mark.
  • HINT:
  • A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
If low quality oil or oil of an inappropriate viscosity is used.
When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
When leaving the idling for a long time, or when driving frequently through heavy traffic.
  • When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.
4. INSPECT FOR OIL LEAK

Start the engine. Make sure that there are no oil leaks from the area that was worked on.

5. INSTALL NO. 2 ENGINE UNDER COVER

Install the No. 2 engine under cover with the 2 bolts.

  • Torque:
  • 29 N*m{ 296 kgf*cm, 21 ft.*lbf}
6. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Install the No. 1 engine under cover with the 10 bolts.

  • Torque:
  • 29 N*m{ 296 kgf*cm, 21 ft.*lbf}
7. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Push in the clip to install the front fender splash shield sub-assembly RH.

Install the 3 bolts and 2 screws.

8. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Install the front No. 2 bumper extension sub-assembly LH with the 4 nuts.

  • Torque:
  • 67 N*m{ 683 kgf*cm, 49 ft.*lbf}
1GR-FE LUBRICATION
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
OIL LEVEL SENSOR