Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 3UR-FE ENGINE CONTROL

IGNITION SYSTEM - ON-VEHICLE INSPECTION

1. PERFORM SPARK TEST

Check for DTCs ().

  • NOTICE:
  • If any DTC is output, perform troubleshooting procedures for that DTC.

Check if sparks occur.

Remove the ignition coils and spark plugs ().

Install the spark plug to the ignition coil and connect the ignition coil connector.

Disconnect the 8 injector connectors.

Ground the spark plug.

Visually check that sparks occur while the engine is being cranked.

  • NOTICE:
Be sure to ground the spark plug when checking.
If the ignition coil has been struck or dropped, replace it.
Do not crank the engine for more than 2 seconds.

Check that the wire harness side connector of the ignition coil with igniter is securely connected.

Result
ResultProceed to
NGConnect securely
OKGo to next step

Perform a spark test on each ignition coil with igniter.

If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.

Result
ResultProceed to
OKReplace ignition coil with igniter
NGGo to next step

Check spark plug.

Result
ResultProceed to
NG Replace spark plug
OK Go to next step

Check the power supply to the ignition coil with igniter.

Turn the engine switch on (IG).

Check that there is battery voltage at the ignition coil positive (+) terminal.

Result
ResultProceed to
NGCheck wiring between engine switch and ignition coil with igniter
OKGo to next step

Check the VVT sensor for intake side ().

Check the VVT sensor for exhaust side ().

Check the camshaft position sensor ().

Check the crankshaft position sensor ().

Check the IGT signal circuit ().

Connect the 8 injector connectors.

Install the ignition coils and spark plugs ().

2. INSPECT SPARK PLUG
  • NOTICE:
Do not use a wire brush for cleaning.
Do not attempt to adjust the electrode gap of a used spark plug.

Check the electrode.

Ignition System - On-Vehicle Inspection. 3UR-FE ENGINE CONTROL. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Using a megohmmeter, measure the insulation resistance.

  • Standard Insulation Resistance:
  • Tester ConnectionConditionSpecified Condition
    Spark plug (terminal part) - Body groundAlways10 MΩ or higher
Text in Illustration
*1Ground

If the insulation resistance is below the specified range, replace the spark plug.


  • HINT:
  • If a megohmmeter is not available, perform the following simple inspection instead.

Alternative inspection method:

Quickly accelerate the engine to 4000 rpm 5 times.

Remove the spark plug.

Visually check the spark plug.


If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

Ignition System - On-Vehicle Inspection. 3UR-FE ENGINE CONTROL. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Check the spark plug for any damage to its threads and insulator.


If there is any damage, replace the spark plug.

  • Recommended Spark Plug:
  • ManufacturerType
    DENSO madeSK20HR11
  • HINT:
  • Maximum electrode gap for a used spark plug: 1.3 mm (0.0512 in.).
  • If the gap is more than the maximum, replace the spark plug.
  • Electrode gap for a new spark plug: 1.0 to 1.1 mm (0.0394 to 0.0433 in.).
  • NOTICE:
  • If adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.

If the electrode has traces of wet carbon, allow it to dry and then clean it with a spark plug cleaner.


  • Standard air pressure:
  • 588 kPa (6.0 kgf/cm2, 85 psi)
  • Standard duration:
  • 20 seconds or less
  • HINT:
  • Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.