Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1UR-FE ENGINE CONTROL
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
READ VALUE USING GTS (THROTTLE POSITION)
REPLACE THROTTLE BODY ASSEMBLY
CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
DTC P2111 Throttle Actuator Control System - Stuck Open
DTC P2112 Throttle Actuator Control System - Stuck Closed
DESCRIPTION
The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM so that the ECM can control the throttle actuator (throttle valve) appropriately in response to driver inputs.
- HINT:
- This ETCS (Electronic Throttle Control System) does not use a throttle cable.
DTC No. | DTC Detection Condition | Trouble Area |
P2111 | Throttle actuator does not close even when the ECM commands it to close (1 trip detection logic). | Throttle actuator Throttle body assembly Throttle valve Wire harness or connector |
P2112 | Throttle actuator does not open even when the ECM commands it to open (1 trip detection logic). | Throttle actuator Throttle body assembly Throttle valve Wire harness or connector |
MONITOR DESCRIPTION
The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.
CONFIRMATION DRIVING PATTERN
- HINT:
GTS Display | Description |
NORMAL | DTC judgment completed System normal |
ABNORMAL | DTC judgment completed System abnormal |
INCOMPLETE | DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions |
N/A | Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
- HINT:
FAIL-SAFE
When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
The ECM continues operating in fail-safe mode until a pass condition is detected, and the engine switch is then turned off.
WIRING DIAGRAM
Refer to DTC P2102 ().
INSPECTION PROCEDURE
- HINT:
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Result | Proceed to |
P2111 or P2112 is output | A |
P2111 or P2112 and other DTCs are output | B |
- HINT:
- If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.
|
| ||||
A | |
2.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.
- OK:
- Throttle valve is not contaminated with foreign objects and moves smoothly.
|
| ||||
OK | |
3.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs ().
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Check the values displayed on the GTS while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
Result | Proceed to |
Value in Data List changes when wire harness is wiggled, or DTC is output* | A |
Other than above | B |
*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector ().
|
| ||||
A | ||
|
4.REPLACE THROTTLE BODY ASSEMBLY |
Replace the throttle body assembly ().
NEXT | |
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs ().
Start the engine, and then fully depress and release the accelerator pedal quickly to fully open and close the throttle valve.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Result | Proceed to |
No DTC is output | A |
P2111 or P2112 is output | B |
|
| ||||
A | ||
|