Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 3UR-FE ENGINE CONTROL

DESCRIPTION

WIRING DIAGRAM

MONITOR DESCRIPTION

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)

REPLACE POWER STEERING OIL PRESSURE SENSOR

CONFIRM WHETHER DTC OUTPUT RECURS

DTC P0550 Power Steering Pressure Sensor Circuit Malfunction

DTC P0552 Power Steering Pressure Sensor Circuit Low Input

DTC P0553 Power Steering Pressure Sensor Circuit High Input

DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.

DTC CodeDTC Detection ConditionTrouble Area
P0550 Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM
P0552 Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM
P0553 Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM

WIRING DIAGRAM

Dtc P0550 Power Steering Pressure Sensor Circuit Malfunction. 3UR-FE ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores DTC(s).


INSPECTION PROCEDURE

  • HINT:
If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
Dtc P0550 Power Steering Pressure Sensor Circuit Malfunction. 3UR-FE ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the C45 ECM connector.

Disconnect the C59 power steering oil pressure sensor connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    C59-2 (PSP) - C45-72 (PSP)AlwaysBelow 1 Ω
    C59-1 (VC) - C45-67 (VCV1)AlwaysBelow 1 Ω
    C59-3 (E2) - C45-98 (ETHA)AlwaysBelow 1 Ω
    C59-2 (PSP) or C45-72 (PSP) - Body groundAlways10 kΩ or higher
    C59-1 (VC) or C45-67 (VCV1) - Body groundAlways10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
2.REPLACE POWER STEERING OIL PRESSURE SENSOR

Replace the power steering oil pressure sensor ().

NEXT
3.CONFIRM WHETHER DTC OUTPUT RECURS

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the tester on.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Read the DTCs.

Result
ResultProceed to
P0550, P0552 and/or P0553 are outputA
No DTC is outputB
B
END
A
REPLACE ECM ()
3UR-FE ENGINE CONTROL
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
SFI SYSTEM