Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1VD-FTV ENGINE CONTROL

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042E OR P045E)

INSPECT EGR VALVE ASSEMBLY

PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION OR CONTROL THE EGR STEP POSITION #2)

REPLACE EGR VALVE ASSEMBLY

CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY)

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DTC P042E Exhaust Gas Recirculation "A" Control Stuck Open

DTC P045E Exhaust Gas Recirculation "B" Control

DESCRIPTION

The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.


In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve lift amount and the throttle valve angle.

P042E (No. 1), P045E (No. 2)
DTC Detection Drive PatternDTC Detection ConditionTrouble Area
After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully releasing accelerator when engine speed is 2000 rpm or more.The target and actual positions of the EGR valve are different for 20 seconds or more.
(1 trip detection logic)
EGR valve stuck
EGR valve does not move smoothly
EGR valve deposits
ECM
While the engine is running, the EGR activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more).
(1 trip detection logic)
Related Data List
DTC No.Data List
P042E
MAF
MAP
EGR Close Lrn. Val.
Target EGR Valve Pos
Actual EGR Valve Pos
P045E
MAF
MAP
EGR Close Lrn. Val #2
Target EGR Valve Pos #2
Actual EGR Valve Pos #2
  • HINT:
Actual EGR valve opening percentage: Fully closed = 0%, fully open = 100%.
If DTC P042E or P045E is stored, the following symptoms may appear:
Stuck closed malfunction
Lack of power: due to fail-safe operation
Intake booming noise
Slight combustion noise
Stuck open malfunction
Black smoke
Lack of power
Vibration at engine stop
Misfire
White smoke
Engine stall

MONITOR DESCRIPTION

When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the electric EGR control valve assembly and illuminates the MIL (1 trip detection logic).


Dtc P042E Exhaust Gas Recirculation A Control Stuck Open. 1VD-FTV ENGINE CONTROL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

  • HINT:
If a large amount of carbon deposits exists in the EGR valve assembly, the following parts possibly also have deposits inside: The intake manifold, EGR cooler, exhaust fuel addition injector assemblies (if equipped), exhaust pipe assemblies (DPF catalytic converter), and other parts related to the exhaust gas.
Be sure to carefully examine "Actual EGR Valve Pos", "Target EGR Valve Pos" and "MAF" in the freeze frame data.
Be sure to carefully examine "Actual EGR Valve Pos #2", "Target EGR Valve Pos #2" and "MAF" in the freeze frame data.

WIRING DIAGRAM

Refer to DTC P0405 ().


INSPECTION PROCEDURE

  • NOTICE:
When cleaning the EGR valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.
After replacing the ECM, the new ECM needs registration () and initialization ().
After replacing the fuel supply pump assembly, the ECM needs initialization ().
After replacing an injector assembly, the ECM needs registration ().
  • HINT:
  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042E OR P045E)

Connect the GTS to the DLC3.

Turn the engine switch on (IG).

Turn the GTS on.

Enter the following menus: Engine and ECT / Trouble Codes.

Read the DTCs.

Result
ResultProceed to
P042E or P045E is outputA
P042E or P045E and other DTCs are outputB
  • HINT:
  • If any DTCs other than P042E or P045E are output, troubleshoot those DTCs first.
B
GO TO DTC CHART ()
A
2.INSPECT EGR VALVE ASSEMBLY

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the GTS on.

Enter the following menus: Engine and ECT / Active Test / Control the EGR Step Position or Control the EGR Step Position #2.

While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos or Actual EGR Valve Pos #2 smoothly changes to the set opening lift amount.

  • OK:
  • Value smoothly changes to within +/- 10% of set opening lift amount.
  • HINT:
EGR valve closed: 0%.
EGR valve open: 95.2%.

Next, after the engine is warmed up, stop the engine and wait for 15 seconds. After that, start the engine again and idle it for 30 seconds. Then stop the engine and wait for 15 seconds. After starting the engine again, read the Data List values while idling.

Enter the following menus: Data List / EGR Close Lrn. Val. or EGR Close Lrn. Val. #2.

Read the values.

  • Standard:
  • 3.5 to 4.5 V
  • Result
    ResultProceed to
    NGA
    OKB
B
Go to step 5
A
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION OR CONTROL THE EGR STEP POSITION #2)
  • HINT:
  • Visually inspect the movement of the EGR valve.

Remove the No. 1 and No. 2 EGR valve assembly ().

Reconnect the No. 1 and No. 2 EGR valve assembly connector.

Connect the GTS to the DLC3.

Turn the engine switch on (IG).

Turn the GTS on.

Enter the following menus: Engine and ECT / Active Test / Control the EGR Step Position or Control the EGR Step Position #2.

Check if the valve of the EGR valve assembly opens/closes when an Active Test is performed.

  • OK:
  • The valve opens/closes.
  • Result
    ResultProceed to
    NGA
    OKB
  • HINT:
  • Remove the deposits if there is a large amount of deposits in the EGR valve assembly or the passage of the intake manifold.
B
Go to step 5
A
4.REPLACE EGR VALVE ASSEMBLY
  • HINT:
  • Before replacing the EGR valve assembly, check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.

When DTC P042E is output:


Replace No. 1 EGR valve assembly ().

When DTC P045E is output:


Replace No. 2 EGR valve assembly ().
NEXT
Go to step 6
5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY)

Remove the EGR valve assembly ().

Visually check the EGR valve assembly for deposits.

  • Result:
  • If there are deposits, clean the EGR valve assembly.
  • NOTICE:
When cleaning the EGR valve assembly, make sure the valve is completely closed.
When cleaning the EGR valve assembly, perform initialization procedure ().
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the EGR valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
  • HINT:
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.

Reinstall the EGR valve assembly ().

NEXT
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Connect the GTS to the DLC3.

Turn the engine switch on (IG).

Turn the GTS on.

Clear the DTCs ().

Turn the engine switch off and wait for 30 seconds or more.

Turn the engine switch on (IG) and turn the GTS on.

After warming up the engine and idling for 60 seconds, the maintain engine speed at 2500 rpm for 40 seconds, the drive vehicle, and perform engine brake deceleration by fully releasing the accelerator when the engine speed is 2000 rpm or more.

  • CAUTION:
  • When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Enter the following menus: Engine and ECT / Trouble Codes.

Confirm that the DTCs is not output again.

NEXT
END
1VD-FTV ENGINE CONTROL
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
ECD SYSTEM w/ DPF