When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected ().

3. REMOVE ENGINE ASSEMBLY

Remove the engine assembly from the vehicle ().

4. CHECK INJECTOR COMPENSATION CODE

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

NOTICE:

When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.

Fuel injector compensation codes are unique, 30 digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

After replacing fuel injector(s) with new one(s), input compensation code(s) of fuel injector(s) into ECM as follows:

HINT:

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each fuel injector.

When you first turn the ignition switch to ON after replacing the ECM or a fuel injector(s), DTC P1601 is set. This is to inform you that registration of a fuel injector compensation code(s) is/are required. Manually clear the DTC upon completion of the compensation code registration.

Input the compensation code(s), which is/are imprinted on the head portion(s) of the new fuel injector(s), into the intelligent tester.

Input the new compensation code(s) into the ECM using the tester.

Turn the tester off and turn the ignition switch off.

Wait for at least 30 seconds.

Turn the ignition switch to ON and turn the tester on.

Clear DTC P1601 stored in the ECM using the tester ().

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.

Turn the tester on.

Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.

Press Next.

Press Next again to proceed.

Select "Set Compensation Code".

Press Next.

Select the number of the cylinder corresponding to the fuel injector compensation code that you want to read.

Press Next.

Press Input.

Manually input the cylinder compensation code using the keyboard on the tester screen. The code is a 30 digit, alphanumeric value printed on the injector head portion.

HINT:

Each fuel injector compensation code is unique. The compensation code for each selected cylinder must be input into the tester correctly.

Confirm that the compensation code for the selected cylinder is correct, and then press OK.

Check that the compensation code displayed on the screen is correct by comparing it with the 30 digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect fuel injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

HINT:

If a wrong compensation code is input or read, return to the Input Value screen by pressing Input.

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

Press Next to register the compensation code in the ECM.

HINT:

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.

Turn the ignition switch off and then turn the tester off.

Wait for at least 30 seconds.

Turn the ignition switch to ON and then turn the tester on.

Clear DTC P1601 stored in the ECM using the tester ().

5. REMOVE NO. 1 INTAKE AIR CONNECTOR PIPE

Disconnect the 4 connectors.

Using a clip remover, detach the 5 wire harness clamps.

Loosen the hose clamp, and remove the bolt and No. 1 intake air connector pipe.

6. REMOVE GENERATOR ASSEMBLY

Remove the nut and bolt, and disconnect the generator positive (+) cable.

Remove the 3 bolts, 2 nuts and generator.

7. REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

Remove the 2 bolts and No. 1 engine oil level dipstick guide.

8. DISCONNECT NO. 2 VENTILATION HOSE

Text in Illustration
*A	w/ DPF
*B	w/o DPF

9. DISCONNECT NO. 2 TURBO WATER HOSE

10. DISCONNECT BREATHER PLUG RH

Disconnect the hose.

Detach the clamp and remove the breather plug RH.

11. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Remove the 3 bolts and No. 1 exhaust manifold heat insulator.

Text in Illustration
*A	w/ DPF
*B	w/o DPF

12. DISCONNECT NO. 1 OUTLET TURBO OIL HOSE

13. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

Disconnect the water hose.

Remove the 3 bolts, 2 nuts, No. 1 turbo water pipe and gasket.

14. REMOVE NO. 1 TURBOCHARGER STAY

Remove the 2 bolts and No. 1 turbocharger stay.

15. REMOVE NO. 1 VENTILATION TUBE SUB-ASSEMBLY

Disconnect the hose.

Remove the union bolt, bolt, No. 1 ventilation tube and gasket.

16. REMOVE NO. 1 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD RH

Remove the union bolt and gasket, and disconnect the No. 1 inlet turbo oil pipe from the cylinder block.

Remove the 10 nuts, 10 collars and No. 1 turbocharger with exhaust manifold RH.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*A	w/ DPF	*B	w/o DPF

Remove the gasket.

w/ DPF:

Remove the 4 bolts, No. 1 exhaust manifold pipe and 2 gaskets.

Remove the 2 nuts and bolt, and separate the No. 1 turbocharger and exhaust manifold RH.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*A	w/ DPF	*B	w/o DPF

Remove the gasket from the No. 1 turbocharger.

17. DISCONNECT NO. 3 VENTILATION HOSE

Text in Illustration
*A	w/ DPF
*B	w/o DPF

18. DISCONNECT BREATHER PLUG LH

Disconnect the hose.

Text in Illustration
*A	w/ DPF
*B	w/o DPF

w/o DPF:

Detach the clamp.

Remove the breather plug LH.

19. DISCONNECT NO. 2 TURBO WATER HOSE

20. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Remove the 3 bolts and No. 2 exhaust manifold heat insulator.

Text in Illustration
*A	w/ DPF
*B	w/o DPF

21. REMOVE NO. 3 TURBO WATER PIPE SUB-ASSEMBLY

Remove the 2 bolts, union bolt, No. 3 turbo water pipe and gasket.

22. REMOVE FRONT WATER BY-PASS JOINT

Remove the front water by-pass joint and gasket.

23. REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

Disconnect the water hose.

Remove the union bolt, bolt, No. 2 turbo water pipe and gasket.

24. DISCONNECT NO. 2 OUTLET TURBO OIL HOSE

25. REMOVE NO. 2 TURBOCHARGER STAY

Remove the 2 bolts and No. 2 turbocharger stay.

26. REMOVE NO. 2 VENTILATION TUBE SUB-ASSEMBLY

Disconnect the hose.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*A	w/ DPF	*B	w/o DPF

Remove the union bolt, bolt, No. 2 ventilation tube and gasket.

27. REMOVE NO. 2 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD LH

Disconnect the 2 connectors from the turbocharger.

Remove the union bolt and gasket, and disconnect the No. 2 inlet turbo oil pipe from the No. 1 oil pan.

Remove the 10 nuts, 10 collars and No. 2 turbocharger with exhaust manifold LH.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Text in Illustration
*A	w/ DPF	*B	w/o DPF

Remove the gasket.

w/ DPF:

Remove the 4 bolts, No. 2 exhaust manifold pipe and 2 gaskets.

Remove the 3 nuts, and separate the No. 2 turbocharger and exhaust manifold LH.

Text in Illustration
*A	w/ DPF
*B	w/o DPF

Remove the gasket from the turbocharger.

28. REMOVE NO. 1 INTAKE AIR CONNECTOR BRACKET

Remove the 2 bolts and No. 1 intake air connector bracket.

29. REMOVE AIR TUBE SUPPORT

Remove the 2 bolts and air tube support.

30. REMOVE NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.

31. REMOVE NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

Disconnect the vacuum hose.

Remove the 2 bolts and No. 4 vacuum transmitting pipe.

32. REMOVE ENGINE MOUNTING BRACKET RH

Remove the 4 bolts and engine mounting bracket RH.

33. REMOVE NO. 1 CYLINDER BLOCK INSULATOR

34. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET

Detach the 2 wire harness clamps.

Remove the bolt and No. 2 intake air connector bracket.

35. REMOVE TURBOCHARGER WIRE

Detach the 3 wire harness clamps.

Remove the 2 bolts and turbocharger wire.

36. REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

w/ Intercooler:

Disconnect the vacuum hose.

Remove the 2 bolts and No. 3 vacuum transmitting pipe.

37. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Remove the union bolt, 2 bolts, No. 2 water by-pass pipe and gasket.

38. REMOVE ENGINE MOUNTING BRACKET LH

Remove the 4 bolts and engine mounting bracket LH.

39. REMOVE NO. 2 CYLINDER BLOCK INSULATOR

40. REMOVE COMPRESSOR BRACKET

Remove the bolt and compressor bracket.

41. REMOVE STIFFENER INSULATOR RH (w/ Intercooler)

Remove the 2 bolts and stiffener insulator RH.

42. DISCONNECT NO. 1 OIL COOLER HOSE

Text in Illustration
*1	No. 1 Oil Cooler Hose
*2	No. 2 Oil Cooler Hose

43. DISCONNECT NO. 2 OIL COOLER HOSE

44. REMOVE CRANKSHAFT PULLEY

NOTICE:

This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.

Text in Illustration
*1	Service Hole
*2	Protrusion

Install the 2 bolts to the bolt holes of the crankshaft rear side.

Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the left of bottom dead center.

Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.

Remove the 3 bolts and crankshaft pulley.

NOTICE:

If the crankshaft pulley cannot be removed, temporarily install a bolt to the crankshaft so that the pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the pulley. Do not tap the pulley V-ribbed belt ribs, as the crankshaft may be damaged.

45. REMOVE TIMING GEAR COVER SPACER (w/ Intercooler)

Remove the 2 bolts and timing gear cover spacer.

46. REMOVE OIL FILTER ELEMENT

Remove the oil filter drain plug.

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

Remove the O-ring from the oil filter drain plug and install it to the drain pipe.

Install the oil filter drain pipe to the oil filter cap and drain the engine oil.

Remove the oil filter drain pipe.

Apply a light coat of engine oil to a new O-ring, and install it to the oil filter drain plug.

Install the oil filter drain plug to the oil filter cap.

Torque:
13 N*m{ 127 kgf*cm, 9 ft.*lbf}

Using SST, remove the oil filter cap.

SST
09228-06501

HINT:

Use a container to catch the draining oil. After the oil filter cap is loosened approximately 4 turns and the cap ribs are vertical, engine oil drains from the gap between the oil filter cap and oil pan.

Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.

47. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

Disconnect the 2 wire harness clamps.

Remove the 3 bolts, 2 nuts and oil filter bracket.

Remove the 2 O-rings.

48. REMOVE ENGINE OIL LEVEL SENSOR

Remove the 4 bolts and engine oil level sensor.

Remove the gasket.

49. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Remove the 10 bolts and 2 nuts.

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the No. 1 and No. 2 oil pans.

50. REMOVE OIL STRAINER SUB-ASSEMBLY

Remove the 2 bolts and oil strainer.

Remove the O-ring from the oil strainer.

51. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

Remove the 20 bolts, 2 nuts and oil reflector plate.

NOTICE:

If the oil reflector plate is deformed, replace it.

HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.

Remove the No. 1 oil pan by prying between the No. 1 oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.

HINT:

Tape the screwdriver tip before use.

Remove the 3 O-rings.

Remove the cylinder block oil hole gasket.

52. REMOVE CAMSHAFT POSITION SENSOR

Disconnect the sensor connector.

Remove the bolt and sensor.

53. REMOVE CRANKSHAFT POSITION SENSOR

Disconnect the sensor wire harness clamp.

Remove the bolt and sensor.

54. REMOVE VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

Disconnect the connector and detach the clamp.

Using pliers, grip the claws of the clips and slide the 2 clips.

Disconnect the 2 heater hoses.

Remove the 2 bolts and heater assembly.

55. REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Remove the bolt and No. 1 idler pulley bracket.

56. REMOVE WATER INLET

Disconnect the No. 2 oil cooler hose from the water pump and clamp.

Remove the 4 bolts and water inlet.

57. REMOVE THERMOSTAT

Remove the thermostat.

Remove the gasket from the thermostat.

58. REMOVE TIMING GEAR COVER INSULATOR (w/ Intercooler)

w/o Viscous Heater:

Remove the 2 bolts and timing gear cover insulator.

w/ Viscous Heater:

Remove the timing gear cover insulator.

59. REMOVE FAN BRACKET SUB-ASSEMBLY

Remove the 4 bolts and fan bracket.

60. REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)

Remove the bolt, cover, No. 2 idler pulley and collar.

61. REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

Remove the 3 bolts and idler pulley bracket.

62. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Remove the 3 bolts and V-ribbed belt tensioner bracket.

Remove the bolt and No. 1 idler pulley.

Remove the 5 bolts and V-ribbed belt tensioner.

63. DISCONNECT INLET WATER HOSE

64. REMOVE STARTER ASSEMBLY

Detach the harness clamp and disconnect the wire harness.

Disconnect the starter connector.

Remove the nut and disconnect the starter wire.

Disconnect the 2 starter hoses.

Remove the 2 bolts and starter.

65. REMOVE STARTER HOSE BRACKET

Remove the 2 bolts and starter hose bracket.

66. REMOVE CLUTCH FLEXIBLE HOSE BRACKET (for Manual Transmission)

Remove the 2 bolts and clutch flexible hose bracket.

67. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET

Remove the 2 bolts and No. 2 intercooler support bracket.

68. REMOVE WATER OUTLET

Disconnect the engine coolant temperature sensor connector.

Remove the 2 bolts, disconnect the water outlet from the No. 2 water hose joint, and remove the water outlet and gasket.

69. REMOVE WATER OUTLET PIPE

Remove the 4 bolts, water outlet pipe and 2 gaskets.

70. REMOVE NO. 1 GLOW PLUG CONNECTOR

Remove the 2 screw grommets and 2 nuts, and disconnect the 2 wire harnesses.

Remove the 8 screw grommets, 8 nuts and 2 glow plug connectors.

Text in Illustration
*a	RH
*b	LH

71. REMOVE GLOW PLUG ASSEMBLY

Using a 10 mm deep socket wrench, remove the 8 glow plugs.

Text in Illustration
*a	RH
*b	LH

HINT:

Before removing the glow plugs, thoroughly clean off all dirt, sand, etc.

72. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ Intercooler)

Disconnect the 2 vacuum hoses.

Remove the bolt and vacuum switching valve.

73. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

w/ Intercooler:

Disconnect the 2 vacuum hoses.

Remove the 3 bolts and vacuum transmitting pipe.

74. REMOVE CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)

Remove the 3 bolts and cylinder head cover silencer.

75. REMOVE CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)

Remove the 3 bolts and cylinder head cover silencer.

76. REMOVE VACUUM PUMP ASSEMBLY (w/ Intercooler)

Remove the 3 bolts and vacuum pump.

Remove the 2 O-rings.

77. REMOVE NOZZLE HOLDER SEAL RH

Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

HINT:

Tape the screwdriver tip before use.

78. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

Remove the 18 bolts, cylinder head cover and gasket.

79. REMOVE NOZZLE HOLDER GASKET RH

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.

80. REMOVE OIL SEPARATOR ASSEMBLY

Remove the 3 bolts, oil separator and gasket.

81. REMOVE NOZZLE HOLDER SEAL LH

Using a small screwdriver, remove the 4 holder seals by prying the portion between each holder seal and the cutout part of the cylinder head cover.

HINT:

Tape the screwdriver tip before use.

82. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Remove the 17 bolts, cylinder head cover and gasket.

83. REMOVE NOZZLE HOLDER GASKET LH

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.

84. REMOVE FUEL INJECTOR RH

Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

Text in Illustration
	Union Bolt

NOTICE:

When removing the nozzle leakage pipe, place a cushion under the pipe.

Be careful not to deform or scratch the union seal surface.

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, holder clamps, washers and bolts in the correct order.

Remove the O-ring from each injector.

Remove the 4 injection nozzle seats from the cylinder head.

85. REMOVE FUEL INJECTOR LH

Remove the union bolt, 4 hollow screws, 5 gaskets and No. 2 nozzle leakage pipe.

Text in Illustration
	Union Bolt

NOTICE:

When removing the nozzle leakage pipe, place a cushion under the pipe.

Be careful not to deform or scratch the union seal surface.

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, holder clamps, washers and bolts in the correct order.

Remove the O-ring from each injector.

Remove the 4 injection nozzle seats from the cylinder head.

86. REMOVE WATER PUMP ASSEMBLY

Remove the 9 bolts, 2 nuts, water pump and gasket.

87. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Remove the 4 nuts and 16 bolts.

Using a screwdriver, remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block.

HINT:

Tape the screwdriver tip before use.

Remove the O-ring from the timing gear case.

88. REMOVE FRONT CRANKSHAFT OIL SEAL

Place the timing chain cover on wooden blocks.

Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.

HINT:

Tape the screwdriver tip before use.

89. SET NO. 1 CYLINDER TO TDC/COMPRESSION

Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.

Turn the crankshaft clockwise to set the No. 1 cylinder to TDC.

With the crankshaft key 45° counterclockwise from the top position, check that the timing marks of the RH and LH camshaft timing gears are aligned. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks as shown below.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 crankshaft pulley set bolts.

90. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Using a T30 "TORX" wrench, remove the 2 screws and crankshaft position sensor plate.

91. REMOVE PUMP DRIVE SHAFT GEAR

Using SST, hold the pump drive shaft gear.

SST
09960-10010(09962-01000,09963-01000)

Remove the 4 bolts and pump drive shaft gear.

92. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 bolts and No. 1 chain tensioner.

93. REMOVE NO. 1 CHAIN TENSIONER SLIPPER

94. REMOVE NO. 1 CHAIN VIBRATION DAMPER

Remove the 2 bolts and No. 1 chain vibration damper.

95. REMOVE NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 TIMING CHAIN

96. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.

Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 bolts and No. 2 chain tensioner.

97. REMOVE NO. 2 CHAIN TENSIONER SLIPPER

98. REMOVE NO. 2 CHAIN VIBRATION DAMPER

Remove the 2 bolts and No. 2 chain vibration damper.

99. REMOVE NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 TIMING CHAIN

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010(09962-01000,09963-01000)

Remove the 4 bolts, No. 2 camshaft timing sprocket and No. 2 timing chain.

100. REMOVE FUEL SUPPLY PUMP DRIVE GEAR NUT

Using SST, hold the idle gear.

SST
09960-10010(09962-01000,09963-00700)

Remove the nut.

Cylinder Head Gasket (W/O Dpf) - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

101. REMOVE IDLE GEAR ASSEMBLY

w/ Intercooler:

Using a 8 mm x 1.25 pitch service bolt with a length of 15 mm or more, fix the idle gear in place.

Torque:
13 N*m{ 133 kgf*cm, 10 ft.*lbf}

Remove the 2 bolts, idle gear thrust plate and idle gear.

102. REMOVE NO. 1 IDLE GEAR SHAFT

103. REMOVE FUEL SUPPLY PUMP DRIVE GEAR

Using SST, remove the fuel supply pump drive gear.

SST
09950-50013(09951-05010,09952-05010,09953-05020,09954-05031)

104. REMOVE FUEL PUMP MOTOR WIRE

Disconnect the 2 connectors and remove the bolt and fuel pump motor wire.

105. REMOVE FUEL SUPPLY PUMP ASSEMBLY

Using a 6 mm hexagon wrench, remove the hexagon bolt. Then remove the 2 nuts and fuel supply pump.

Remove the O-ring.

106. REMOVE V-BANK SILENCER

107. REMOVE TIMING GEAR CASE SUB-ASSEMBLY

Remove the 22 bolts, 2 nuts and timing gear case shown in the illustration.

Remove the 2 O-rings and timing gear case gasket.

108. REMOVE NO. 1 AND NO. 2 CAMSHAFTS

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

Torque:
8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Loosen the 2 union bolts.

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.

Remove the No. 1 and No. 2 camshafts.

109. REMOVE NO. 3 AND NO. 4 CAMSHAFTS

Using an 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

Torque:
8.0 N*m{ 82 kgf*cm, 71 in.*lbf}

Loosen the 2 union bolts.

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.

Remove the 2 union bolts, and No. 3 and No. 4 oil feed pipes.

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.

Remove the No. 3 and No. 4 camshafts.

110. REMOVE NO. 2 CAMSHAFT BEARING CAP

111. REMOVE NO. 5 CAMSHAFT BEARING CAP

112. REMOVE NO. 1 VALVE ROCKER ARM

Remove the 16 No. 1 valve rocker arms.

HINT:

Be sure to arrange the removed parts for each installation position separately.

113. REMOVE NO. 2 VALVE ROCKER ARM

Remove the 16 No. 2 valve rocker arms.

HINT:

Be sure to arrange the removed parts for each installation position separately.

114. REMOVE NO. 1 VALVE LASH ADJUSTER ASSEMBLY

Remove the 16 No. 1 valve lash adjusters.

HINT:

Be sure to arrange the removed parts for each installation position separately.

115. REMOVE NO. 2 VALVE LASH ADJUSTER ASSEMBLY

Remove the 16 No. 2 valve lash adjusters.

HINT:

Be sure to arrange the removed parts for each installation position separately.

116. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

NOTICE:

Be careful not to drop washers into the cylinder head.

Head warpage or cracking could result from removing bolts in an incorrect order.

HINT:

Be sure to arrange the removed parts for each installation position separately.

117. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

NOTICE:

Be careful not to drop washers into the cylinder head.

Head warpage or cracking could result from removing bolts in an incorrect order.

HINT:

Be sure to arrange the removed parts for each installation position separately.

118. REMOVE NO. 1 CYLINDER HEAD GASKET

119. REMOVE NO. 2 CYLINDER HEAD GASKET

1VD-FTV ENGINE MECHANICAL

Land Cruiser URJ200 URJ202 GRJ200 VDJ200

CYLINDER HEAD GASKET w/o DPF