Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - CRUISE CONTROL
CRUISE CONTROL SYSTEM - DATA LIST / ACTIVE TEST
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Cruise Control / Data List.
According to the display on the intelligent tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| CCS Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) | Actual vehicle speed displayed | - |
| CCS Mem Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph) | Actual vehicle speed stored in memory | - |
| Cruise Operation Status | Transmission range sensor signal / ON or OFF | ON: Shift lever in D OFF: Shift lever not in D | for A/T |
| Clutch switch signal / ON or OFF | ON: Clutch pedal released OFF: Clutch pedal depressed | for M/T | |
| Cruise Control | Cruise control / ON or OFF | ON: Cruise control operating OFF: Cruise control not operating | - |
| CCS Indicator M-CPU | CRUISE main indicator light (Main CPU) / ON or OFF | ON: CRUISE main indicator light on OFF: CRUISE main indicator light off | - |
| CCS Ready M-CPU | Cruise control system standby condition (Main CPU) / ON or OFF | ON ←→ OFF: Changes each time main switch pushed | - |
| Main SW M-CPU | Cruise control main switch (Main CPU) / ON or OFF | ON: Cruise control main switch (Main CPU) on OFF: Cruise control main switch (Main CPU) off | - |
| Stop Light SW M-CPU | Stop light switch signal (Main CPU) / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Cancel Switch | CANCEL switch / ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off | - |
| SET/COAST Switch | -SET switch / ON or OFF | ON: -SET switch on OFF: -SET switch off | - |
| RES/ACC Switch | +RES switch / ON or OFF | ON: +RES switch on OFF: +RES switch off | - |
| Brake Cancel Switch | Stop light switch signal | ON: Brake pedal depressed OFF: Brake pedal released | for 1GR-FE, 1VD-FTV (w/ DPF), 3UR-FE |
| Throttle Opening Angle | Cruise throttle opening angle / min.: 0 deg, max.: 125 deg | Actual demanded throttle angle | for 1GR-FE, 1UR-FE, 3UR-FE |
| Fuel injection quantity / min.: 0%, max.: 100% | Actual demanded fuel injection quantity | for 1VD-FTV | |
| # Codes | Number of trouble codes / Min.: 0, Max.: 255 | - | - |
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the intelligent tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Indicat. Lamp Cruise | Cruise control indicator light operation | ON / OFF | - |
| Indicat. SET | Cruise control SET indicator light operation | ON / OFF | - |