DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)
INSPECT CRUISE CONTROL MAIN SWITCH
INSPECT CRUISE CONTROL SWITCH WIRE
INSPECT SPIRAL CABLE
CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
CRUISE CONTROL SYSTEM - Cruise Control Switch Circuit
DESCRIPTION
The cruise control main switch is used to operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCELERATION), TAP-UP, and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCELERATION) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCELERATION) and CANCEL.
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH) |
Using the intelligent tester, read the Data List ().
Cruise Control| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Main SW M-CPU | Cruise control main switch (Main CPU) / ON or OFF | ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off | - |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off | - |
| SET/COAST Switch | -SET switch signal / ON or OFF | ON: -SET switch on
OFF: -SET switch off | - |
| RES/ACC Switch | +RES switch signal / ON or OFF | ON: +RES switch on
OFF: +RES switch off | - |
- OK:
- The intelligent tester display changes according to operation of cruise control main switch.
| OK | |
| |
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE ()
|
|
| 2.INSPECT CRUISE CONTROL MAIN SWITCH |
Remove the cruise control main switch ().
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 3 | Neutral | 1MΩ or higher |
| Pushed to +RES | 235 to 245 Ω |
| Pushed to -SET | 620 to 640 Ω |
| Pushed to CANCEL | 1510 to 1570 Ω |
| Main switch pushed off | 1MΩ or higher |
| Main switch pushed on | Below 2.5 Ω |
| | REPLACE CRUISE CONTROL MAIN SWITCH ()
|
|
|
| 3.INSPECT CRUISE CONTROL SWITCH WIRE |
Remove the cruise control switch wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| z37-3 - 3 | Always | Below 1 Ω |
| z37-4 - 1 |
| | REPLACE CRUISE CONTROL SWITCH WIRE |
|
|
If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or the spiral cable.
Check spiral cable.
Set the spiral cable to the center position ().
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| z37-3 - E12-1 (CCS) | Always | Below 1 Ω |
| z37-4 - E12-2 (ECC) |
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
- As the spiral cable may break, do not rotate the spiral cable more than the specified amount.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| z37-3 - E12-1 (CCS) | Always | Below 1 Ω |
| z37-4 - E12-2 (ECC) |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
Disconnect the E12 spiral cable connector.
Disconnect the A38*1 or A52*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1GR-FE LHD, 1UR-FE LHD, 3UR-FE| Tester Connection | Condition | Specified Condition |
| E12-1 (CCS) - A38-45 (CCS) | Always | Below 1 Ω |
| E12-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| E12-2 (ECC) - Body ground | Always | Below 1 Ω |
for 1GR-FE RHD, 1UR-FE RHD| Tester Connection | Condition | Specified Condition |
| E12-1 (CCS) - A52-45 (CCS) | Always | Below 1 Ω |
| E12-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| E12-2 (ECC) - Body ground | Always | Below 1 Ω |
for 1VD-FTV LHD| Tester Connection | Condition | Specified Condition |
| E12-1 (CCS) - A38-40 (CCS) | Always | Below 1 Ω |
| E12-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| E12-2 (ECC) - Body ground | Always | Below 1 Ω |
for 1VD-FTV RHD| Tester Connection | Condition | Specified Condition |
| E12-1 (CCS) - A52-40 (CCS) | Always | Below 1 Ω |
| E12-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| E12-2 (ECC) - Body ground | Always | Below 1 Ω |
Result| Result | Proceed to |
OK
(for 1GR-FE) | A |
OK
(for 1UR-FE) | B |
OK
(for 3UR-FE) | C |
OK
(for 1VD-FTV) | D |
| NG | E |
| |
|
| |
|
| |
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
