INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE

INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

INSPECT DIFFERENTIAL RING GEAR BACKLASH

REMOVE DRIVE PINION COMPANION FLANGE REAR NUT

REMOVE REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

REMOVE DIFFERENTIAL CASE ASSEMBLY

REMOVE DIFFERENTIAL DRIVE PINION

REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

REMOVE DIFFERENTIAL RING GEAR

INSPECT RUNOUT OF DIFFERENTIAL CASE

REMOVE REAR DIFFERENTIAL CASE BEARING

DISASSEMBLE DIFFERENTIAL CASE

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

• Maximum Runout:

• Runout	Specified Condition
  Vertical runout	0.10 mm (0.00394 in.)
  Lateral runout	0.10 mm (0.00394 in.)

If the runout is more than the maximum, replace the companion flange.

Using a dial indicator, measure the ring gear runout.

• Maximum runout:
• 0.05 mm (0.00197 in.)

If the runout is more than the maximum, replace the ring gear.

Using a dial indicator, measure the ring gear backlash.

• Standard backlash:
• 0.10 to 0.20 mm (0.00394 to 0.00787 in.)

• HINT:

• Measure at 3 or more positions around the circumference of the ring gear.

If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

Using SST and a hammer, unstake the nut.

• SST
• 09930-00010

Using SST to hold the companion flange, remove the nut.

• SST
• 09330-00021(09330-00030)

Using SST, remove the companion flange.

• SST
• 09950-30012(09951-03010,09953-03010,09954-03010,09955-03030,09956-03040)

Using SST, remove the oil seal from the differential carrier.

• SST
• 09308-10010

Using SST, remove the front bearing (inner race) from the drive pinion.

• SST
• 09556-22010

If the front bearing is damaged or worn, replace the bearing.

Remove the 2 bolts and 2 adjusting nut locks.

Place matchmarks on the bearing caps and differential carrier.

Remove the 4 bolts, 2 bearing caps, 2 adjusting nuts and 2 bearings (outer race).

Remove the differential case from the differential carrier.

• HINT:

• Tag the 2 case bearing outer races to show the location for reassembly.

Remove the differential drive pinion from the differential carrier.

Using SST and a press, press out the bearing (inner race).

• SST
• 09950-00020

If either the drive pinion or ring gear is damaged, replace them as a set.

Using a brass bar and hammer, tap out the bearing (outer race).

Using a brass bar and hammer, tap out the bearing (outer race).

Place matchmarks on the ring gear and differential case.

Remove the 12 ring gear set bolts.

Using a plastic-faced hammer, tap on the ring gear to disconnect it from the differential case.

Install the differential case to the differential carrier.

Using a dial indicator, measure the differential case runout.

• Maximum runout:
• 0.04 mm (0.00157 in.)

If the runout is more than the maximum, replace the differential case and side bearings as a set.

Remove the differential case from the differential carrier.

Using SST, remove the 2 side bearings (inner race) from the differential case.

• SST
• 09950-00020
  09950-00030
  09950-40011(09957-04010)
  09950-60010(09951-00480)

Place matchmarks on the differential case LH and RH.

Remove the 8 bolts uniformly, a little at a time.

Using a plastic-faced hammer, disconnect the differential case LH and RH.

Remove the 2 side gear thrust washers, 2 side gears, spider, 4 pinion gears and 4 pinion gear thrust washers.